NXG Technology NX-OVC Weatherproof Volume Control Enclosure - Manual (Page 2)

NX-OVC Specifications
Enclosure & Faceplate Material:
Weatherproof ABS
Gasket Material:
Silica gel PVC
Dimensions (including enclosure
mounting feet, conduit opening
& face plate):
5 1 /
8
˝ (130mm) H x
3 7 /
8
˝ (98mm) W x
3 5 /
16
˝ (84mm) D
(Note: Volume control knob will
add approx. 3/4˝ - 1˝ depth
depending on control shaft length)
Designed for use with Class 2
wiring only
16648 North 94th Street
Scottsdale, AZ 85260
1-800-733-0008
www.nxgtech.com
NXG One-Year Limited Warranty
If the NXG product proves to be defective in workman-
ship or materials within one year from the date of the
original customer’s purchase, we will, at our option,
repair or replace the defective product.
Limitation of Implied Warranties
Any implied warranties, including warranties of mer-
chantability and fitness for a particular purpose, are
limited in duration to the length of this warranty.
Exclusion of Certain Damages
NXG’s liability for any defective product is limited to
repair or replacement of the product at our option.
NXG shall not be liable for incidental or consequential
damages of any kind or character because of product
defects. Some states do not allow limitations on how
long an implied warranty lasts and/or do not allow the
exclusion or limitation of incidental or consequential
damages, so the above limitations and exclusions may
not apply.
This Warranty Does Not Cover:
• Damage caused by abuse, accident, misuse, negli-
gence, or improper operation.
• Any product whose serial number has been altered,
defaced, or removed.
• Products that have been altered or modified.
• Normal wear and maintenance.
• Damages caused by shipping. (All claims for shipping
damage must be made with the carrier.)
Warranty Service
Warranty service must be performed by an authorized
service center, usually a NXG dealer or its authorized
agent. You may obtain a list of authorized service cen-
ters by contacting NXG. All warranty repairs must be
accompanied by the original bill of sales. No other doc-
ument is acceptable or is required. This warranty gives
you specific legal rights, and you may also have other
rights which vary from state to state.
NXG reserves the right to revise specifications without notice.
3. Layout your wiring system using 3/4˝ PVC conduit and run one piece up to the NX-OVC and check
the fit of all connections before you glue the joints.
4. Run wires from your receiver/amplifier to the NX-OVC and connect to your volume control as outlined
in your volume control and receiver’s manual. Then run the wires from the volume control to your out-
door speakers as outlined in your speaker’s manual.
5. Once all the electrical connections have been completed, check the system for proper operation.
6. If everything is working OK, go ahead and mount the volume control into the NX-OVC enclosure using
two of the supplied screws. Then permanently mount the NX-OVC to the wall and cement all the conduit
connections using PVC adhesive. Double check all conduit connections for a good watertight seal.
Inadequate sealing of any conduit joint could cause moisture buildup inside the conduit system and the
NX-OVC enclosure, which could cause erratic operation or failure of the volume control.
7. Make sure the gasket is seated properly in the face plate and press it into place. The center hole of
the gasket should stretch over the volume control shaft to create a watertight seal.
8. Screw the cover plate to the enclosure using four of the supplied screws.
9. Finally, place the supplied knob on the volume control shaft.
Fig. 2 Typical NX-OVC System Setup
Receiver
Weatherproof
Speakers
3/4˝ PVC Conduit
NX-OVC
House