NXG Technology NX-HDMIX-WP-IR-50 - HDMI over dual Cat5e/6/7 - Manual (Page 2)

SPECIFICATIONS
Operating Temperature Range -5 to +35C(-41 to +95 )
Operating Humidity Range 5 to 90%RH (No Condensation)
Input Video Signal 0.5-1.0 Volts P-P
Input DDC Signal 5 volts p-p (TTL)
Support Video Format DTV/HDTV:480i/576i/480P/576P/720P/1080i/1080P
HDMI Output HDMI 1.3, HDCP 1.1
Support Audio Format DTS-HD Master Audio0Dolby true-HD etc.
Transmission Distance 1080P 8-bit 50m(Maximum) over CAT5E/CAT6 /24AWG/Solid
(Recommend to use 23AWG Cat6 cable)
Power consumption 3 watts (Maximum)
Dimension (L x W x H) 115 x 70 x 35mm
IR Wavelength & Frequency Wavelength: 940nm, frequency: 38kHz
Net Weight 260g(Pair)
Note 1: Specifications are subject to change. Mass and dimensions are approximate.
Note 2: When in 36Bit deep color mode, we suggest setting the HDMI source device to 1080i or 720p.
CONNECTIONS TRANSMITTER (TX)
2 3
OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS
Front Panel Rear Panel
RECEIVER (RX)
Front Panel Rear Panel 1. HDMI output port
2. Power input port
3. IR/RX
4. Indicator of HDMI input
5. Indicator of power input
6. CAT5e/6 input ports
1. HDMI input port
2. Power input port
3. IR/TX
4. Indicator of HDMI input
5. Indicator of power input
6. CAT5e/6 output ports
CONNECTING THE NX-HDMIX-WP-IR-50
1) Connect the HDMI source output into the HDMI IN on the front plate of the
NX-HDMIX-WP-IR-50 (TX). (TX = Transmitter / RX = Receiver)
2) Connect two CAT-5E or CAT6 cables to both the outputs of NX-HDMIX-WP-IR-50 (TX)
and inputs of NX-HDMIX-WP-IR-50 (RX). Please pay attention to the correct connection of
the two cables, CAT5e/6-1->CAT5e/6-1 (The RJ45 connections must follow EIA/TIA 568B).
3) Connect the HDMI source input into HDMI OUT on the front plate of the
NX-HDMIX-WP-IR-50 (RX).
4) Connect the IR TX UNIT into NX-HDMIX-WP-IR-50 (TX). Permanently affix the TX IR emitter
over the source components IR window by removing the adhesive backing. In order to work
properly, the emitter must be placed on the source component IR receiver window.
5) Connect the IR RX UNIT into NX-HDMIX-WP-IR-50 (RX). The RX IR receiver should be
placed in direct line of sight with the handheld remote. Consider affixing the IR receiver on
the TV frame or base.
NOTE: In some cases the power adapter could be taken off. The power adapter is needed when
the signal source isn’t sufficient enough to drive the HDMI signal. Gently Insert/Extract cables.
TYPICAL
APPLICATION
MAINTENANCE
When cleaning this unit, use only a dry soft cloth. Never use an alcohol
based cleaner, paint thinner or other harsh cleaning chemical. Be careful not
to dislodge the TX IR emitter from its permanent position on the Source IR window.
PRODUCT SERVICE
1) Damage requiring service: The unit should be serviced by qualified service personnel if:
(a) The DC power supply cord or AC adaptor has been damaged;
(b) Objects or liquids have damaged the unit;
(c) The unit has been exposed to rain;
(d) The unit does not operate normally or exhibits a marked change in performance;
(e) The unit has been dropped or the cabinet damaged.
2) Do not attempt to service the unit beyond that described in these operating instructions.
Unauthorized service may result in fire, electric shock, or other hazards and will void
all warranty.