Atec Amrel-SPS Series - Manual (Page 3)

REMOTE CONTROL
/ MONITOR On/Off control via contact closure, 6-120 VDC or 12-240 VAC, and TTL or
CMOS switch, output voltage and current monitor, OVP limit set, summary fault status
PARAMETER SPECIFICATION
FRONT PANEL AND REMOTE DIGITAL PROGRAMMING
Voltage A-Panel: ±0.5% of full-scale + 1 Digit K-Panel: ±0.1% of full-scale
Current A-Panel: ±0.5% of full-scale + 1 Digit K-Panel: ±0.4% of full-scale
Overvoltage Protection (OVP) ±1% of full-scale output
REMOTE DIGITAL READBACK
Voltage ±0.15% of full-scale
Current ±0.4% of full-scale
REMOTE ANALOG PROGRAMMING
Constant Voltage ±0.25% of full-scale output for 0-5V range (±0.5% 0-10V range)
Constant Current ±0.8% (40-800V output), ±1.0% (10-30V output) of full-scale output
Overvoltage Protection (OVP) ±1% of full-scale output
REMOTE ANALOG READBACK
Voltage ±1% (40-800V output), ±0.5% (10-30V output) of full-scale output
Current ±1% (40-800V output), ±0.5% (10-30V output) of full-scale output
RESISTIVE ANALOG PROGRAMMING
Constant Voltage (0-100%) 0-5 kΩ
Constant Current (0-100%) 0-5 kΩ
VOLTAGE ANALOG PROGRAMMING
Constant Voltage (0-100%) 0-5 VDC or 0-10 VDC
Constant Current (0-100%) 0-5 VDC or 0-10 VDC
REMOTE SENSING Terminals are provided to sense output voltage at point of load. Maximum line drop 5% of rated voltage per
line for 40-100V models, line drop 1V of rated voltage per line for 10-20V models, 1.5V for 30V models, 2%
of rated voltage per line for models 160V and greater. (Greater line drop is allowed, but output regulation
specifications no longer apply).
REMOTE ANALOG CONTROL
Input to Output Isolation
The control signal return for Non-Isolated Analog programming is connected to the negative output termi-
nal. Under no condition should the negative terminal exceed 300V to earth ground. The maximum voltage
from control signal return of the Remote Isolated Analog programming (option) to the negative output
terminal is 600V.
PHYSICAL 3U MODELS (10V-30V) 3U Models (40V-800V) 6U MODELS (40V-600V)
WIDTH 19.00 in (48.3 cm) 19.00 in (48.3 cm) 19.00 in (48.3 cm)
DEPTH 28.09 in (71.4 cm) 26.4 in (67.1 cm) 27.06 in (63.8 cm)
HEIGHT 5.25 in (13.3 cm) 5.25 in (13.3 cm) 10.5 in (26.7 cm)
WEIGHT (Physical) (4kW, 10V 15V) ≈<65 lbs (29 kg)
(5kW, 20V 30V) ≈<65 lbs (29 kg)
(8kW, 10V 15V) ≈<85 lbs (39 kg)
(10kW, 20V 30V) ≈<85 lbs (39 kg)
(12kW, 10V 15V) ≈<110 lbs (50 kg)
(15kW, 20V 30V) ≈<110 lbs (50 kg) (5kW) ≈ 40 lbs (18 kg)
(10kW) ≈ 60 lbs (27 kg)
(15kW) ≈ 80 lbs (36 kg) (20kW) ≈ 120 lbs (54 kg)
(25kW) ≈ 140 lbs (64 kg)
(30kW) ≈ 160 lbs (73 kg)
Important Notes:
1) Specifications are subject to change without notice
2) The SPS Series power supplies are intended for indoor use only.
Note: AMREL is the registered trademark of AMERICAN RELIANCE, INC and is being used by permission