Hunter 99118 Basic On/Off Handheld - Manual (Page 2)

www.HunterFan.com
1.888.830.1326
Troubleshooting Safe-Exit
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This device complies with RSS-210 of Industry Canada. Operation is
subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to
radio communications. However there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following
measures: Reorient or relocate the receiving antenna, Increase the
separation between the equipment and receiver, Connect the equipment
into an outlet on a circuit different from that to which the receiver is
connected. Consult the dealer or an experienced radio/TV technician for
help. Note: Any changes or modifications to the transmitter or receiver
not expressly approved by Hunter Fan Company may void one’s authority
to operate this remote control.
Read and Save These Instructions
This product conforms to UL Standard 507.
WARNINGS
Fan will not start
• Make sure the power is on at the
circuit breaker and the wall switch.
• Make sure the battery is working.
• Make sure that the transmitter and
receiver are paired.
• Check wire connections inside of
the canopy.
Remote control of fan is erratic
• Make sure the battery is installed
correctly.
• Install a fresh battery.
Transmitter only works when held
at close range
• Change battery.
Lights do not dim
• Check to see if a CFL bulb is
installed. The control has a feature
that automatically detects CFL bulbs
and turns off dimming if a CFL bulb
is installed.
CFL bulbs flicker
• Turn the light switch off and back
on. Within three minutes, hold down
the Fan Off button while pressing
the Light Off button twice. If the
problem is not corrected, repeat the
process up to three times.
Pairing Maintenance
Installing or changing the battery
To access the battery compartment
remove the small Phillips head screw
that secures the battery door to the
transmitter assembly. Replace with a
CR2032 battery when necessary. The
battery should be installed with the
positive (+) side up.
Phillips
Head
Screw
Battery
Door
• Press the fan OFF button for at
least three seconds to initiate the
Safe-Exit Mode.
• The lights will flash for visual
confirmation.
• The lights will stay on 50%
brightness for 15 seconds and
then begin to dim. After a total
of 30 seconds, the lights will be
completely off.
Note: For CFL lighting, the lights
will stay on 100% brightness
for 30 seconds. After a total of
30 seconds, the lights will be
completely off.
The Safe-Exit Program gives
you about thirty seconds of
light when you turn the lights
off to exit the room before the
lights go out. To use Safe-Exit:
M0057-01 • 01/15/14 • © Hunter Fan Company
HUNTER FAN COMPANY CONTROL LIMITED WARRANTY
The Hunter Fan Company makes the following limited warranty to the original purchaser
of the Control (“Control”): Your Control is warranted to be free from defects in
material and workmanship for a period of one year from the date of sale. If the Control
malfunctions or fails within the warranty period due to a defect in material or workmanship
we will replace it free of charge. IF THE ORIGINAL PURCHASER CEASES TO OWN THE
CONTROL, THIS WARRANTY AND ANY IMPLIED WARRANTY, INCLUDING BUT NOT
LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR
A PARTICULAR PURPOSE, ARE VOIDED. THIS WARRANTY IS IN LIEU OF ALL OTHER
EXPRESS WARRANTIES. THE DURATION OF ANY IMPLIED WARRANTY, INCLUDING,
BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE, IN RESPECT TO ANY CONTROL, IS
EXPRESSLY LIMITED TO THE PERIOD OF THE EXPRESS WARRANTY SET FORTH
ABOVE FOR SUCH CONTROL. This warranty excludes malfunctions or failures which
were caused by repairs by persons not authorized by us, mishandling, improper installation,
modifications, or damage to the Control while in your possession, or unreasonable use.
This warranty does not apply to batteries or to deterioration or damage to the product
caused by the use of faulty batteries. To obtain a replacement, return your Control postage
prepaid along with proof of purchase to Hunter Fan Company Service Department at
7130 Goodlett Farms Pkwy., Memphis, TN 38016. IN NO EVENT SHALL HUNTER
FAN COMPANY BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES.
SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED
WARRANTY LASTS OR THE EXCLUSION OR LIMITATIONS OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY
NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND
YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
ON
Turn
Pow
er
Within 3 minutes of restoring power
to the fan, press both the Fan OFF
button and the Fan ON button for at
least 4 seconds. Your fan will turn on to
indicate successful syncing. If it does
not, turn off power to your fan, wait
1 minute then try again. If using the
transmitter with multiple fans, repeat
this process for each fan.
Note: The remote must be paired
before the fan will operate. Fan Operation:
Press and quickly release the ON or OFF
button on the remote control to turn
the fan OFF or ON.
To change the fan speed, slowly pull
the fan pull-chain switch to select the
desired speed.
Light Operation:
Press and quickly release the ON or OFF
button on the remote control to turn
the light OFF or ON. (Light will come
ON at maximum brightness.)
Operation
Fan OFF Fan ON
Light
Control
Fan
Control
If you have problems installing or operating your fan, do not return this
product to the dealer. Call our Consumer Affairs Hotline.
1-888-830-1326
Use the pull-chain switch on the
fan to set the fan speed to the HIGH
position before operation.
IMPORTANT