Audiovox AX-45 - Manual (Page 6)

128-6992
6 of 8
6
"Programming System Features" shown later in this installation guide to learn the operation of the valet/program/manual
override switch.
POWER DOOR LOCK HARNESS
3PIN White Plug w/3 Wires; Green, Blue & Blue/Red
The connection of the power door lock/unlock wires has already been explained. Route the three pin connector to the unit
and plug the connector into the mating white three pin connector shell of the control module. Do not force the connector,
it will only plug in one way.
PROGRAMMING FEATURES:
There are seven (7) Programmable Features on this system. Study the list below, keeping in mind the features and their
defaults, (how it comes programmed from the factory), and decide how best to program the UNIT for your particular
installation.
Programmable Features:
Features 1 Chirp 2 Chirp 3 Chirps Default
First Passive Arming Active Arming Active Arming
Second Ignition D/L ON Ignition D/L OFF Ignition D/L OFF
Third Ignition D/UL ON Ignition D/UL OFF Ignition D/UL OFF
Fourth Chirps ON Chirps OFF Chirps ON
Fifth Passive D/L Active D/L Active D/L
Sixth Siren Output Horn Output Horn Output
Seventh 800ms D/L Pulse 3.5 Sec. D/L Pulse 800ms D/L Pulse 800ms Door Lock
Double 800ms D/UL Pulses
To Program These Features:
Entering the Programming Mode involves operating the Ignition Switch and the Valet/Program/Manual Override Switch in
a particular sequence. This sequence is very time dependent, in other words it must be performed quickly in order for you
to enter the mode. This sequence is also only one step different from the Transmitter Programming Mode, so make
certain you perform the sequence properly.
Upon entering the Programming Mode, the system is immediately set to allow adjustment of the First Programmable
Feature. That First feature, "Passive or Active Arming", can then be set ON or OFF by pressing the lock button of the
transmitter. The system confirms that it is set to adjust the First feature by repeatedly flashing the LED once, with a pause
in between each flash. The system will then report how the feature has been set by the number of chirps heard after
pressing the transmitter button. Toggling the Valet/Program/Manual Override Switch once again will advance you to the
Second Programmable Feature, confirmed by a repeating two LED flashes, with a pause in between each flash, etc.
It is important to note that when you first enter the Programming Mode, you are automatically positioned to adjust the First
Programmable Feature and that the Valet/Program/Manual Override Switch allows you to toggle from there through each
of the six more programmable features. However, it will not allow you to return to any feature once you have toggled past
it. Should you accidentally toggle past the feature you wanted to program, you must exit and re-enter the Programming
Mode and then adjust the feature you missed.
It is also important to note that you may toggle past as many programmable features as you wish without having to adjust
them. Each time you toggle forward to a new feature, the horn will chirp the appropriate number of times (1, 2, or 3 times)
to indicate how that feature is currently set, and the LED will flash the appropriate number of times to indicate the number
of the feature (First through Seventh) that you are set to adjust. For example, you might enter the mode and toggle the
Valet/Program/Manual Override Switch 3 times in order to adjust the Fourth programmable feature. The system would
respond with 1 Chirp, and the LED would begin to flash 4 Flashes, pause, and repeat. This has told you that the system
is ready for you to adjust the Fourth programmable feature, and that it is currently programmed for Chirps ON. A single
press of the lock button of the transmitter will cause the system to produce 2 Chirps. This signifies that you have
changed the programming to Chirps OFF. Please follow the programming procedure on the next page, and refer to the
list of the Programmable Features above when programming the system.
To program these selectable features;
Action System Response LED Response
Turn ignition on No response
Turn the valet switch on then off 3 times 1 Chirp - LED 1 flash
Within 3 seconds, turn ignition Off Short chirp, then long chirp
First Then On 2 chirps = active arming 1 Flash pause
Press transmitter Lock button to change 1 chirp = passive arming
or