Impulse rBOX610 - Manual

* All specifications and photos are subject to change without notice. 321
rBOX610
Robust Din-rail Fanless Embedded System
with RISC-based (iMX-287) Processor 4 COM,
2 CAN Bus and DIO
● Fanless design
● RISC-based module (iMX-287) processor
● 128MB DDR2 SDRAM onboard
● 1 eMMC 4 GB onboard
● 1 SDHC socket for storage expansion (easy to access)
● 4 COM ports
● 2 CAN bus
● RTC battery function
● LED indicators
● SNMP V1/V2c
● Wide range DC power input (12 - 48V) with terminal block
● Ready-to-run embedded Linux operating system
● Wide temperature operation of -40°C ~ +70°C
Introduction
Hardware Specifications
rBOX610 cost-effective din-rail fanless embedded system utilizes the low power
RISC-based module (iMX-287) processor and is designed to withstand temperatures
ranging from -40°C to +70°C for using in extreme operating environment and industrial
automation applications.
rBOX610 features 4 RS-232/422/485 serial ports, dual LANs, 4 digital input channels,
4 digital output channels, 2 CAN bus and 1 eMMC onboard 4 GB & 1 x SDHC socket
for storage expansion (easy to access) in a compact, IP40 protected, industrial-strength
robust case. Two power paths input minimize the risk of data loss in the event of a single
power failure. Its vertical din-rail form factor makes it easy to install the system in a
small cabinet. Due to the RISC-based architecture, rBOX610 will not generate a lot of
heat while being operated. The ready-to-run rBOX610 is specially designed for remote
control/monitoring management applications like unmanned control room, industrial
machine, automatic parking lot, traffic cabinet and more.
Standard Color Sliver-Black
Construction Extruded aluminum and heavy-duty steel, IP40
CPU iMX-287, ARM9 16-bit RISC CPU, 454 MHz
System Board Q7M100
System Memory 1 x DDR2 128 MB SDRAM onboard
System I/O Outlet Serial Port 4 x RS-232/422/485 (COM 1 ~ 4)
COM 1~3 with TX/RX/RTS/CTS signals
RS-232/422/485 interface select by
software
LAN 2 x 10/100Mbps Ethernet
Magnetic isolation protection 1.5KV
System I/O Outlet USB 1 x USB 2.0
USB power distribution control by
software
CAN 2 CAN 2.0 B (Phoenix connector, non-
isolation)
Meets ISO 11898 standard
Software control termination resistor
120 ohm can high speed up to 1Mbit/s
for transmit/receive
DIO 1 x DIO (4-IN/4-OUT)
DI :
Input channels : 4, source type
Input voltage : 0 to 30VDCDigital input
levels for dry contacts :
-Logic level 0: close to GND
-Logic level 1: open
Digital input levels for wet contacts :
-Logic level 0: +10V to +24V (DI to COM-)
-Logic level 1: +3V max.
DO :
Output channels : 4, sink type
Output current: Max. 200 mA per
channel
On-state voltage : 24VDC nominal, open
collector to 30V
Optical isolation protection 2 KV
Console Port DB9 connector
For user setting with debug
RTC Battery onboard
Provides power for the internal real time
clock & calendar
Ideal for vibration environment &
reduces maintenance efforts
Power Input 2 power paths with terminal block
Alarm Contact One relay output with current
0.5A@30VDC
Features
Rear view
Front view
Easy-to-access interface
NEW
Extended
Temperature
Fanless Low Power EN60950-1 IP40 UL508 Isolation
Din-rail kit
Wireless
(3G/GPRS)
4 COM
LED indicators (power, alarm,
ready/active, COM, wireless)
RISC-based Module
(iMX-287) Processor
Power DC-In
Console port
SDHC slot
SIM sot
DIO (4-In/4-Out)
2 CANBus