NewAir ACP-1300H - Manual (Page 3)

High Mid Low
3.Operating Instructions
8
1.When first plugging in the ACP-1300H,
a tone indicating that the power is connected
will sound. After pressing the "On" button,
the unit will start in Auto Mode and display
the current room temperature.
2.To select the mode, press the "Mode" button. This will then cycle the
ACP-1300H through the "Auto ,""Heating," "Fan,""Cooling, "and "Dehumidify"
options.
3.When adjusting the temperature, keep in mind that the ACP-1300H is
adjustable between 60 and 88 F. To set the temperature, press the "Temperature"
button until the desired temperature is displayed. The air conditioner will now
cool the room to that temperature. After five seconds of setting your desired
temperature, the display will then revert back to displaying the current room
temperature.
O O
4. To adjust the fan speed, press the "Speed button." This will allow the
ACP-1300H to cycle through the "High,""Medium," and "Low" speed
options.
5.
6.
To turn off the unit, press the "Off" button. The air conditioner will
cease operation and a tone will sound.
1.For fresh air, press the "Fresh Air" button while the unit is running.
This will then engage the built-in ion generator.
MODE SPEED TIMER WIND
TEMP ON/OFF
WIND
Please Note:
While in dehumidification mode, the unit will automatically set the fan speed to
"Low". The ACP-1300H will not allow fan speed adjustments, nor will adjusting
the temperature affect the unit's operation.
In addition, while in fan mode, adjusting the temperature will not affect the unit's
operation. If the ACP-1300H is in standby mode, the remote control's memory
function will turn on. Your settings will be stored in the unit's memory, and when
used next, it will operate according to the last saved settings only the timer
function will need to be reset (if you are using this function).
Auto Cooling Dehumidify Fan Heating
3. Operating Instructions
9
Setting the Timer Function:
To set the timer function, press the "Timer" button and enter the time that
you would like the unit to shut down. You will then have the option of setting
the time for the unit to resume function (ranging from half an hour to 12 hours,
in half hour increments). You can also exit the timer function at that time.
While the unit is in standby mode, you can also set the operation times by
pressing the "Timer" button. Enter the time in which you would like the air
conditioner to begin operating, and you will then be able to program the time
at which you want the unit to go back into standby mode (ranging from half
an hour to 12 hours, in half hour increments). You can also exit the timer
function at that time (Note: While in the set time frame, the air conditioner will
display a countdown of the remaining time until the next mode is initiated).
To adjust the airflow, if you would like to have the airflow oscillated from the
ceiling to the floor, press the "Oscillation" button on the remote control. Right
to left airflow can then be set by manually adjusting the louvers.
Please Note:
When turning off the unit, VFD indicators will appear "Off" until the sweep
shuts down.
Battery Installation:
3. Operating Instructions
10
Remote Control Panel
Battery
Battery Cover Panel
1.Open the battery compartment by sliding down the battery cover
panel.
2.Remove and discard old batteries replace with new batteries
3.Replace the battery panel back onto the remote.
Please Note:
1.The polarity of the batteries must match the indicator in the remote control.
2.Do not mix old and new batteries in the remote control.
3.To prevent corrosion, remove the batteries if the remote control will not be
used for an extended period of time.
Water Tank
Drainage
3. Operating Instructions
11
When the ACP-1300H is in operation, the condensed water will be drained into
the water tank. If the water tank is full, a buzzer will sound 20 times, and the
VFD indicator will display an "E2" error warning. At that time, the unit will cease
operation, and if you wish to restart the unit, the water tank must be emptied by
taking the following steps:
1.Turn off the unit.
2.Remove the rubber plug. The condensed water will then flow out.
3.After the water is emptied, replace the rubber plug.
4.Restart the unit.
Drainage Hole Rubber Plug