NewAir ACP-1300H - Manual (Page 4)

3. Operating Instructions
12
Air Exhaust Hose
The hot air exhaust conducts the hot, moist air produced by the unit away from
the space you are cooling. The window kit and exhaust hose can also be moved
from room to room with the unit. You can exhaust the ACP-1300H by following
one of the following two methods:
Exhaust the hot air through a window or sliding glass door (a window
kit extension may be necessary). Open the window or sliding glass
door, install the window kit, and connect the exhaust hose. 1.
2. If an existing window or sliding glass door cannot be used, a custom
opening through a wall or ceiling can be cut out in order to facilitate
the exhaust hose.
Please Note:
The hot air must be exhausted in order for the unit to produce a cooling effect.
When the ACP-1300H is not in use, safely store away the exhaust hose in a
clean, dry place.
50cm
50cm
50cm
50cm
Exhaust Hose
3. Operating Instructions
13
3.The length of the exhaust hose
should not be extended past 6.5 feet.
Replacement hoses are available for
purchase through your NewAir
vendor. We also recommend that
you use only certified NewAir re-
placement parts.
1.The exhaust hose can extend
from 1.8 feet to 6.5 feet. The
shorter the hose , the better
the cooling effect .
2. The hose should be as straight
as possible, as sharp or unnece
-ssary bends in the hose will prevent effective airflow.
This will subsequently result in overheating and possible
shut-down of the unit.
4. Troubleshooting
Problems Possible Causes Suggested Solutions
The unit doesn't work.
14
Troubleshooting Your ACP-1300H Portable Air Conditioner
Before investing in repairs, check to see if any of the following apply to you:
There could be power trouble.
1.The power cord is not
plugged in.
2.The circuit breaker has
been tripped.
3.There is a problem with
the socket or outlet.
4.Either the power cord is
damaged, or the fuse
needs to be replaced.
1.Connect the power cord corre-
ctly.
2.Reset the circuit at the breaker
box.
3.Change the socket or outlet.
4.Take the unit to a qualified techn-
ician and have the fuse replaced
(fuse specification: 3A/250V).
The unit stops working on its own.
Either the timer has been
activated or the temperature
in the room is lower than the
set temperature.
Either turn the timer off or wait
for the room temperature to rise.
There is no cool air coming out
of the unit when it is in cooling
mode.
1.The room temperature is
lower than the set temp-
erature.
2.The evaporator is frosted
over.
1.Wait for the room temperature
to rise to resume normal
operation.
2.Allow the evaporator to defrost
and normal operation will
resume.
There is no cool air coming out of
the unit when it is in dehumidifying
mode.
1.The evaporator is frosted
over.
2.The unit is eliminating frost.
Allow the evaporator to defrost
andnormal operation will resume.
Error code E2 is displayed on the
control pane.l The water tank is full. Empty the water tank and restart
the unit.
Error code E4 is displayed on the
control panel.
The coil pipe is damaged. Replace the coil pipe.
Error code E1 is displayed on the
control panel.
1.The voltage is too high or
too low.
2.The unit is damaged.
1.Restart the unit when the voltage
is normal.
2.Have the unit repaired by your
NewAir dealer or at a professional
repair center.
Please Note:
Never service your ACP-1300H portable air conditioner by yourself.
If your unit needs to be repaired, please contact your NewAir dealer
or a professional repair center for assistance.
5. Electric Diagram
15