Atlas Sound FA62T-8MB User Manual

Page 3

Advertising

Specifications subject to change without notice

Printed in U.S.A.

000704 ATS001372 RevD 7/04

SL1-2019

2.31

One

1601 JACK MCKAY BLVD. / ENNIS, TEXAS 75119 U.S.A.

TELEPHONE: (800) 876-3333

/ FAX (800) 765-3435

AtlasSound.com

POWER

70.7V

FREQUENCY

SENSITIVITY

WOOFER

MATCHES

WEIGHT-LESS

MODEL

RATING

TAPS

RESPONSE (±7dB)

(1W/1M)

MAGNET WT

DRIVER

ENCLOSURE

TILE BRIDGE

FA62T-8MB

50 Watts

2, 4,

63Hz - 20kHz

88dB

6" Poly Cone

14 oz.

Coaxially Mounted

FA95-8, FA97-8

4 Lbs.

(Transformer 8, 16, 32

(in FA97-8 Enc.)

Average

Butyl Rubber

(398g)

PEI Dome Tweeter

(1.81kg.)

Limited)

Surround

SPECIFICATIONS

FA62T-8MB

Shown in FA97-8 Enclosure,

with FA720-8 Grille

and FA81-8 Tile Bridge

MOTORBOARD ASSEMBLIES

Atlas Sound has also addressed retrofit and “division of labor” installations with a new “motor-
board” version of the Strategy Series II. Model F62T-8MB is comprised of: 6" speaker/trans-
former/selector switch and front plate. The footprint of the F62T-8MB is identical to a standard
FA Series 8" speaker component, which allows a motorboard to fit into all current Strategy
Series 8" enclosures in the exact manor as a regular FA speaker.

FA62T-8MB – “MOTORBOARD”

ARCHITECTS AND ENGINEERS SPECIFICATIONS

The loudspeaker system shall be Atlas Sound F62T-8MB. System shall include a high per-
formance 6" coaxial loudspeaker and tap selector switch mounted to a ported mounting
plate appropriately sized to match Atlas Sound FA95-8, FA97-8 enclosures. When used with
the FA97-8 enclosure frequency response for the system shall be 63Hz to 20KHz (±7dB).
Sensitivity shall be 88dB average. Loudspeaker shall be comprised of a 6" coaxial cone type
driver. Cone shall be constructed of polypropylene with a butyl rubber surround. The19mm
tweeter shall be constructed of PEI. Magnet shall be a minimum of 10oz. (264g) and the voice
coil diameter shall be 1" (25mm). Transformer shall be (70.7/100V) volt type with 2, 4, 8, 16
and 32 watt primary taps (@70.7V). 12" stripped & tinned wiring pigtails shall be terminated to
the tap selector switch for convenient hook-up. The motorboard assembly shall weigh no more
than 4 lbs. (1.81kg) The motorboard assembly shall be the Atlas Sound FA62T-8MB.

The loudspeaker system shall be Atlas Sound FAP62T. System shall
include a high performance 6" coaxial loudspeaker, ported bass reflex
enclosure and press-fit grille for conventional ceiling installation.

Frequency response for the system shall be 63Hz to 20kHz (±7dB).
Sensitivity shall be 88dB average.

Loudspeaker shall be comprised of an 6" coaxial cone type driver. Cone
shall be constructed of polypropylene with a butyl rubber surround.
The 19mm tweeter shall be constructed of PEI. Magnet shall be a mini-
mum of 10oz. (264g) and the voice coil diameter shall be 1" (25mm).

Transformer shall be (70.7/100V) volt type with 2, 4, 8, 16 and 32
watt primary taps (@70.7V) with a front mounted tap selector switch to
include transformer bypass setting for 8 ohm direct coupled operation.

Enclosure shall be a deep drawn steel enclosure design acoustically
treated with fiberglass lining. Internal volume shall be 475 cubic inches.
To facilitate connection in conduit systems, enclosure shall be equipped
with an access panel covering a recessed terminal cup. This cover shall
provide a combination

⁄

" (19mm inside diameter) / 1" (25mm inside diam-

eter) knock-out on the side access and a top access compression fitting/
strain relief to facilitate flexible conduit up to 22mm outside diameter or 1"
(25mm inside diameter) conduit when the compression fitting is removed.

External wiring shall be accomplished via a removable lockable wiring
connector with screw-down terminals to provide both secure wire ter-
mination and pre-wiring capability before loudspeaker installation. The
4 pole locking connector shall facilitate in/out connections and shall be

located in the recessed area behind the conduit access panel.

Seismic support eye shall be provided on top of enclosure for additional
suspension point when used in drop tile ceilings. Construction of enclo-
sure shall be a minimum of 18 gauge deep drawn galvanized metal.

The system shall include a support backing plate to reinforce the ceiling
material and tile support rails for use on either 2' x 4' (609mm x 1219mm)
or 2' x 2' (609 x 609mm) suspended ceiling tiles. This assembly can all
be installed from beneath the ceiling tile.

Overall front face diameter shall not exceed 12.5" (318mm); overall
depth from the bottom of the ceiling shall not exceed 8.48" (215mm).
Grilles shall be press-fit, manufactured from 24 gauge perforated
steel mesh and finished in white epoxy. Round grill shall be 10.48"
(266mm) Diameter.

The loudspeaker shall weigh no more than 9.5 lbs (4.41kg).

The loudspeaker shall be the Atlas Sound FAP62T.