Nova-Tech 4364 TRACEABLE WATERPROOF FOOD HACCP THERMOMETER - Manual

TRACEABLE
WATERPROOF
FOOD HACCP
THERMOMETER
INSTRUCTIONS
DiSplaY MeSSageS
appears when the battery power is at the
optimum level.
appears when the battery power is low.
Measurements are possible; however, the batteries
should be replaced (see the “Battery Replacement”
section).
appears when the battery power is
insufficient. Measurements are not possible and
the batteries must be replaced (see the “Battery
Replacement” section).
“HI” appears when the temperature measured
exceeds the maximum temperature measurement
range.
“LO” appears when the temperature measured
exceeds the minimum temperature measurement
range.
“Er2” appears when the unit is exposed to rapid
changes in ambient temperature.
“Er3” appears when the ambient temperature is
below 32° F (0° C) or above 122° F (50° C).
“Er” appears when the unit needs to be reset. To
reset the unit, remove the batteries, wait 2 minutes
and then re-install the batteries.
all opeRational DifficUltieS
If this thermometer does not function properly for
any reason, replace the batteries with new high
quality batteries (see Battery Replacement section).
Low battery power can occasionally cause any
number of “apparent” operational difficulties.
Replacing the batteries with new fresh batteries will
solve most difficulties.
®
BatteRY ReplaceMent
Erratic readings, faint readings, no display, or
appearing on the display are all indications that
the batteries must be replaced.
To replace the batteries:
1. Remove the rubber plug from the battery cover.
2. Remove the battery cover screw.
3. Remove the battery cover.
4. Remove the exhausted batteries and replace
them with two (2) new AAA alkaline batteries.
Make certain to install the new batteries in the
directions indicated in the battery compartment.
5. Replace the battery cover.
6. Replace the battery cover screw and tighten
securely.
7. Replace the rubber plug. This plug is required in
order to achieve a water resistant seal.
WaRRantY, SeRVice, oR RecaliBRation
For warranty, service, or recalibration, contact:
CONTROL COMPANY
4455 Rex Road
Friendswood, Texas 77546 USA
Ph. 281 482-1714 • Fax 281 482-9448
E-mail [email protected] • www.control3.com
Control Company is ISO 9001 Quality-Certified by
DNV and ISO 17025 accredited as a Calibration
Laboratory by A2LA.
MetalS (Typical Emissivity Values)
SURface ...........................................................eMiSSiVitY
iron and Steel
Cast iron (polished) ............................................................0.2
Cast iron (tumed at 100 o C) ...............................................0.45
Cast iron (tumed at 1000 o C) .....................................0.6 to 0.7
Steel (ground sheet) ...........................................................0.6
Mild steel ..................................................................0.3 to 0.5
Steel plate (oxidized) ..........................................................0.9
Iron plate (rusted) ...................................................0.7 to 0.85
Cast iron (rough) rusted ....................................................0.95
Rough ingot iron .................................................................0.9
Molten cast iron ..................................................................0.3
Molten mild steel .......................................................0.3 to 0.4
Stainless steel (polished) ....................................................0.1
Stainless steel (various) ...........................................0.2 to 0.6
aluminum
Polished aluminum ........................................................... 0.1*
Aluminum (heavily oxidized) .............................................0.25
Aluminum oxide at 260 o C ...................................................0.6
Aluminum oxide at 800 o C ...................................................0.3
Aluminum Alloys, various ........................................0.1 to 0.25
Brass
Brass (polished) ................................................................ 0.1*
Brass (roughened surface) .................................................0.2
Brass (oxide) ......................................................................0.6
copper
Copper (polished) ........................................................... 0.05*
Copper (oxide) ....................................................................0.8
Molten copper ...................................................................0.15
lead
Lead (polished) ................................................................. 0.1*
Lead (oxide at 25 o C) ...........................................................0.3
Lead (oxide) ........................................................................0.6
nickel and its alloys
Nickel (pure) ..................................................................... 0.1*
Nickel plate (oxide) ...................................................0.4 to 0.5
Nichrome ............................................................................0.7
Nichrome (oxide) ..............................................................0.95
Zinc (oxidized) .................................................................. 0.1*
Galvanized iron ...................................................................0.3
Tin-plated steel ................................................................. 0.1*
Gold (polished) ................................................................. 0.1*
Silver (polished) ................................................................ 0.1*
Chromium (polished) ........................................................ 0.1*
non-MetalS (Typical Emissivity Values)
SURface eMiSSiVitY
Refractory & Building Materials
Red brick (rough) ....................................................0.75 to 0.9
Fire clay ............................................................................0.75
Asbestos ...........................................................................0.95
Concrete .............................................................................0.7
Marble .................................................................................0.9
Carborundum ....................................................................0.85
Plaster ................................................................................0.9
Alumina (fine grain) ..........................................................0.25
Alumina (coarse grain) .....................................................0.45
Silica (fine grain) .................................................................0.4
Silica (coarse grain) ..........................................................0.55
Zirconium silicate up to 500 o C ..........................................0.85
Zirconium silicate at 850 o C .................................................0.6
Quartz (rough) ....................................................................0.9
Carbon (graphite) .............................................................0.75
Carbon (soot) ....................................................................0.95
Timber (various) .......................................................0.8 to 0.9
Miscellaneous
Enamel (any color) .............................................................0.9
Oil paint (any color) ..........................................................0.95
Lacquer ...............................................................................0.9
Matte black paint ..................................................0.95 to 0.98
Aluminum lacquer ...............................................................0.5
Water ................................................................................0.98
Rubber (smooth) .................................................................0.9
Rubber (rough) .................................................................0.98
Plastics (various, solid) ...........................................0.8 to 0.95
Plastic films (0.05 mm thick) ...................................0.5 to 0.95
Polythene film (0.03 mm thick) .................................0.2 to 0.3
Rubber (smooth) .................................................................0.9
Rubber (rough) .................................................................0.98
Plastics (various, solid) ...........................................0.8 to 0.95
Plastic films (0.05 mm thick) ...................................0.5 to 0.95
Polythene film (0.03 mm thick) .................................0.2 to 0.3
Paper and cardboard ..........................................................0.9
Silicone polish .....................................................................0.7
*Emissivity varies with purity
Control Company Cat. No. 4364
Traceable ® is a registered trademark of Control Company.
© 2009 Control Company. 92-4364-00 Rev. 0 071709
eMiSSiVitY taBle