Altinex DA1222AT - Manual (Page 7)

DISTRIBUTION AMPLIFIERS
6
INSTALLATION 6
Step 1. Before you plug in the power cord into
the unit, please verify that the voltage
rating of 110V/220V on the FUSE CLIP
located on the rear of the unit is the
same as the power outlet.
Step 2. Connect the female end of the power
cord to the DA1222AT and plug the
male end into the power outlet. The
power indicator LED on the front panel
will turn ON. This indicates that the unit
is operational.
Step 3. Connect the video output of the source
(computer, or interface, or any other
high-resolution source) to the input of
the DA1222AT using a high quality
coaxial-type cable. If the source offers a
VGA-type 15-pin HD connector, then
use a special cable - Altinex part #
MS8102CA (15-pin HD Male to 5 BNC
Male 6 feet cable) may be used.
NOTE: You may have to use an
interface (DA1910SX or VA6855WM)
with your source computer to provide
the appropriate signal format type and
to allow the use of a local monitor. Do
not use a Y-cable or monitor breakout
cable to connect the computer to the
DA1222AT because this will affect the
quality of the high-resolution input
signal.
Step 4. Connect the output channels of the
DA1222AT to the display devices (i.e.
monitors and/or projectors) using a
cable less than 10 feet with the
appropriate number of channels.
Step 5. Verify that the picture quality and
bandwidth on all displays is good.
CONGRATULATIONS! YOU ARE DONE.
OPERATION 7
The DA1222AT will operate successfully as long
as cables are attached properly and other
technical specifications are followed. There are no
other adjustments necessary to operate the unit.
ACCESSORIES 8
Model No. Description
TABLE MOUNT BRACKETS
TM1271 1 U High, ½ Rack-Wide
TM1272 1 U High, ½ Rack-Wide with 15-pin
HD connector plate
TM1273 1 U High, ½ Rack-Wide with SNAP-IN
connectors
TM1274 1 U High, ½ Rack-Wide with SNAP-IN
and power connectors
RACK/TABLE MOUNT HARDWARE
DA1293FC 19”-1U Rack Mount Shelf fits two ½
rack wide units
DA1294FC 19”-1U Rack Mount Ears. Holds one
1/2 rack wide unit
HIGH RESOLUTION 5-CHANNEL
COAX CABLE
CB4203MR 3 feet, 5-BNC to 5-BNC
CB4206MR 6feet, 5-BNC to 5-BNC
CB4212MR 12 feet, 5-BNC to 5-BNC
CB4225MR 25 feet, 5-BNC to 5-BNC
CB4250MR 50 feet, 5-BNC to 5-BNC
CHB4275MR 75 feet, 5-BNC to 5-BNC
CB42100MR
100 feet, 5-BNC to 5-BNC
CB42150MR 150 feet, 5-BNC to 5-BNC
SUPER HIGH RESOLUTION 5-
CHANNEL COAX CABLE
CB4406MR 6feet, 5-BNC to 5-BNC
CB4412MR 12 feet, 5-BNC to 5-BNC
CB4425MR 25 feet, 5-BNC to 5-BNC
CB4450MR 50 feet, 5-BNC to 5-BNC
CB4475MR 75 feet, 5-BNC to 5-BNC
CB44100MR 100 feet, 5-BNC to 5-BNC
CB44150MR 150 feet, 5-BNC to 5-BNC
VGA TO RGB ADAPTER CABLES
MS8102CA 15-pin HD Male to 5 BNC Male, 6ft
MS8104CA 15-pin HD Male to 5 BNC Male, 15ft
MS8105CA 15-pin HD Male to 5 BNC Male, 50 ft
MS8112CA 15-pin HD Female to 5 BNC Male, 6ft
MS8114CA 15-pin HD Female to 5 BNC Male, 15ft
If you experience any problems, please call
1-800-258-4623 or 1-714-990-2300 for
international calls.