Farm Star HK-11062 - Manual (Page 7)

5
A S S E M B LY (continued)
NOTE: Use of Stabilizer Bars
Some implements such as post hole diggers, rear
blades, landscape rakes, and rear 3 pt. scoops, you
need to install the stabilizer bars to eliminate side
movement of the hitch to control the implement.
With other implements, such as 3 pt. plows, disc
harrows, field cultivators, and harrows, it is best to
remove the stabilizer bars and allow the hitch side
movement. This makes it easier to steer the tractor and
minimize side pressure on the hitch and the implement
when turning.
NOTE: When connecting the hitch to an implement, it will
be necessary to remove the lift arm end of the stabilizer
bar from the lift arm. This allows the lift arm to swing out
and be installed on the pull pin of the implement.
After the lift arms are connected to the implement, the
stabilizer bars need to be reconnected and adjusted so
that the implement is centered behind the tractor.
Attach the center link to the main frame using the 3 / 4 ”
toplink pin and linchpin provided.
Tighten all bolts before using this kit.
Connect your hoses from the tractor’s hydraulic system
to the hydraulic cylinder on the hitch kit.
Check to make sure that the hoses are located so that
they will not be pinched or chafed by any of the moving
parts on the hitch. Avoid sharp bends with hydraulic
hose.
Use a good quality thread sealant on all connections.
DO NOT USE TEFLON TAPE (small pieces of tape can
get into hydraulic valves and components, causing
problems).
Check the hydraulic relief valve setting on the tractor to
make sure it is properly set (refer to tractor specifications
by IHC).
When the hydraulic system is connected, cycle the
hydraulic cylinder a few times to remove any air bubbles.
Check to make sure that the hitch is operating smoothly.
O P E R AT I O N
Two holes are provided on the lift arms to connect to the
lower ends of the leveling assemblies.
The forward holes will provide the greatest lifting range
for the ball ends of the lift arms. The rear holes will allow
heavier loads to be handled by the hitch.
The adjustable screw type leveling assemblies will
provide additional adjustment in the lifting height of the
hitch.
NOTE: BE SURE THAT AT LEAST 1 1 / 4 ” OF THREAD
ON EACH END IS ENGAGED INTO THE THREADED
BARREL OF THE LEVELING ASSEMBLIES.
The adjustable screw type top link can also be short-
ened or lengthened to adapt different implements and
can be used to obtain various degrees of pitch on the
implements you are using.
The ball sockets on the lift arms are two-way balls, so
they will accommodate both Category I or Category II lift
pins on the implement. If the drawbar or implement has
Category I (
7 / 8 ”) pins, make sure the balls are turned so
that the 7 / 8 ” diameter holes are used.
The stabilizer bars should be used whenever possible,
as they not only prevent side sway, but provide rigidity
and stability to the unit – plus added strength. The stabi-
lizer bars are threaded stubs so their length can be
adjusted so the spread of the lift arms can be increased
or decreased to accommodate the different width of
Category I and Category II tools.
NOTE: Figure A shows an optional swinging drawbar
bracket and mounting hardware that allows you to use
the existing swinging drawbar on your tractor. Order
optional drawbar bracket #861190.
The HK-1106 (single hydraulic cylinder) kit is designed
to lift up to 1600 pounds. The HK-11062 (double
hydraulic cylinder) kit is designed to lift up to 2400
pounds. This capacity of lift is calculated at a point 24” to
the rear of the lift arms. The lifting capacity is dependent
on the pressure and condition of the tractor’s hydraulic
system. You will also find that the closer the load is kept
to the tractor, the more you will be able to lift.
NOTE: The size of the tractor will be the main determin-
ing factor in how much weight you can handle. (A Model
M can handle more that a Model H and a Model 560 can
handle more than an MTA.)
NOTE: If the larger 1 1 / 8 ” diameter holes are used with the
smaller 7 / 8 ” pins, the ball sockets will “hole out,” for which
Worksaver cannot be responsible. If you do use smaller
7 / 8 ” diameter lift pins and the larger 1 1 / 8 ” diameter ball
holes, be sure to use lift arm adapter bushings to elimi-
nate the excess play or loose fit.
I N S T R U C T I O N S (continued) I N S T R U C T I O N S (continued)
Read manual before operating.
C A U T I O N !
S A F E T Y T R A I N I N G
• Know your controls and how to stop tractor, engine,
and PTO quickly in an emergency. READ THIS
MANUAL AND THE ONE PROVIDED WITH YOUR
TRACTOR.
• To avoid accident or injury, do not allow anyone to
operate this equipment without proper instructions.
Any person who operates this equipment must be
instructed in and be capable of the safe operation of
the tractor, implement and all controls.
• Do not allow children to operate this machine.
• Always wear relatively tight and belted clothing to
avoid entanglement in moving parts. Wear sturdy,
rough-soled work shoes and protective equipment for
eyes, hands, and hearing. Never operate tractor in
bare feet, sandals, or sneakers.
• Operate only in daylight or good artificial light.
• Ensure implement is properly mounted, adjusted and
in good operating condition.
• Ensure that all safety shielding and safety signs are
properly installed and in good condition.
W A R N I N G !
MAKE SURE THAT ALL OPERATING AND SERVICE
PERSONNEL KNOW THAT IN THE EVENT
HYDRAULIC FLUID PENETRATES THE SKIN, IT
MUST BE SURGICALLY REMOVED WITHIN A FEW
HOURS BY A DOCTOR FAMILIAR WITH THIS FORM
OF INJURY, OR GANGRENE MAY RESULT.
Be sure your tractor is in good condition and
properly equipped with counterweights. Read all the
safety precautions and make sure all tractor
operators are familiar with the safety rules of tractor
operation.
C A U T I O N !
W A R N I N G !
▲ Keep clear of rotating parts; stay on tractor seat
until all motion has stopped.
▲ Be sure tractor engine is off and key is removed
before making any adjustments.
▲ Do not get under machine to make measurements
or adjustments without securely blocking imple-
ment first.
Figure 1. Tractor Stability
W A R N I N G !
When using 3 pt. hitch equipment, a minimum 20%
of tractor and equipment weight must be on tractor
front wheels. Without this weight, tractor could tip
up, causing possible loss of control and possible
personal injury or death. The weight may be attained
with a front end loader, front wheel weights, ballast
in tires or front tractor weights. When attaining a
minimum 20% of tractor and equipment weight on
the front wheels, you must not exceed the ROPS
weight certification. Weigh the tractor and equip-
ment. DO NOT GUESS OR ESTIMATE!
A heavy load can cause instability in driving a trac-
tor. Make sure the front of the tractor is properly
counter-balanced with weights. Always drive slowly
– especially around turns. An unstable tractor could
steer badly and possibly tip over, causing injury or
death.
W A R N I N G !
Be sure your tractor is in good condition and
properly equipped with counterweights. Read all the
safety precautions and make sure all tractor
operations are familiar with the safety rules of tractor
operation.
W A R N I N G !
6