Foredom H.15SJ - Manual

Instructions for Foredom Hammer Handpieces
H.15, H.15D, and H.15SJ
Hammer Handpieces are supplied with an anvil point (HP10177).
If anvil points are reshaped they must also be polished with a
grinding wheel or sandpaper.
Operation: The H.15, 15D, and 15SJ handpieces can be operated at speeds
from 0–5,000 RPM (or intermittently up to 7,500 RPM). Use at higher
speeds will create excessive heat which will damage the handpiece.
Changing Points: Insert the pin through the cross hole in the anvil
or carbide stylus point. Hold the handpiece firmly and unscrew the point
in a counterclockwise direction. (Right hand thread.) A new point can be
installed by threading it into the nosepiece and tightening it with the pin.
Adjusting Impact: The impact of the stroke is adjusted by turning the
knurled ring on the handpiece– counterclockwise towards the tip for a
lighter impact– and clockwise towards the back of the handpiece for a
heavier impact.
Lubrication: Before disassembling nosepiece, be sure to clean off any
dirt or other foreign matter to prevent it from falling inside the handpiece.
Lubricate after every 10 hours of use. Apply no more than 2 drops of oil into
the oiling hole located on the barrel of the handpiece and into the hole on
the rear of the duplex spring connection of the H.15D.
Several other hammer tips are shown inside and are available separately.
Always wear safety glasses when using power tools.
LIMITED WARRANTY
The Foredom Electric Company warrants its product to be free of
defects in material or workmanship for a period of 90 days after
purchase. During the warranty period, the defective product will be
repaired or replaced without charge or, at our option, the purchase
price will be refunded. This warranty does not cover damage caused
in transit or by accident, misuse, or ordinary wear. ALL IMPLIED
WARRANTIES, INCLUDING BUT NOT LIMITED TO WARRANTIES OF FITNESS
AND MERCHANTABILITY, ARE HEREBY LIMITED IN DURATION TO A PERIOD
ENDING 90 DAYS FROM DATE OF PURCHASE, AND WE WILL NOT BE LIABLE
OR RESPONSIBLE FOR ANY SPECIAL OR CONSEQUENTIAL DAMAGES. Repair
or replacement will be made at our option if the product is returned
post-paid to:
The Foredom Electric Company
16 Stony Hill Road, Bethel, CT USA 06801
All warranty repairs must be done at the factory at the above address.
We will not pay any shipping or transportation charges. This warranty
only covers the original purchaser of the product. Some states do not
allow limitations on how long an implied warranty lasts, so the above
limitations may not apply to you. This warranty gives you specific legal
rights, and you may also have other rights which vary from state
to state.
FOREDOM ®
The Foredom Electric Company
16 Stony Hill Road, Bethel, CT 06801 USA
• www.foredom.com
Phone: 203-792-8622 • Fax: 203-796-7861
Form No. 1233 n 3/10 Printed in USA
Ball Nose 3/32 ″ HP10171
(2.35mm) dia.
Fine Point .015 ″ HP10172
(.4mm) dia.
Square 3/32 ″ HP10173
(2.35mm)
Cylinder 7/32 ″ HP10175
(6mm) dia.
Rectangle 3/32 ″ x 3/16″ HP10176
(2.35mm x 4.8mm)
Bezel Rocker 5/16 ″ x 1/4″ HP10179
(8mm x 6.4mm)
Threaded Anvil Points for Hammer Flex Shaft and Micromotor Handpieces
The six new threaded anvil points fit Foredom Flex Shaft Hammer Handpieces,
Foredom Micromotor Hammer Handpiece and the Swiss made Badeco Hammer
Handpiece. They are heat treated steel made to the finest specifications and
finished with black oxide.
Other Foredom Hammer Tips
for H.15, H.15D, and H.15SJ
Handpieces
Carbide Stylus HP10212
4-48UNF-2A thread
Diamond Tip
Pavé Point A-R15PT
4-48UNF-2A thread
Flat Top Taper HP10177
4-48UNF-2A thread (included with H.15,
H.15D and H.15SJ
handpiece)
AK101
6-Pc Anvil Point Kit
Includes: Ball Nose, Fine
Point, Square, Cylinder,
Rectangle, and Bezel
Rocker shown at left.
Accessories for Hammer Handpieces
Made in USA. 0-5,000 Strokes per Minute Max Speed.
Contact your favorite Foredom dealer
or visit our website for more details.
www.foredom.com