Foredom C.FCH-2 - Manual

Qty Description Part No. Item
1 Cover CP10852B 1
1 Trigger Switch, 250V CP11027 2
1 Base CP10851 3
1 Front Base Pad CP10859 4
1 Screw, 6−32 x 1" CP10856 5
1 Washer, #6 CP10862 6
1 Rear Base Pad CP10860 7
1 Male Cordset or Substitute Option CP10541 8
2 Strain Relief CP10003−3 9
1 Female Cordset (FCT−2)
Female Cordset (FCH−2) CP10542
CP10868 10
1 Wire Connector CP11029 11
Description Part No.
CPOption20 CP10545 No Plug, Europe
CPOption21 CP10553 Male, United Kingdom
CPOption22 CP10554 Male, Continental Europe
CPOption25 CP10555 Male India 10A
CPOption26 CP10556 Male, Austrailia
Cordset Option
Parts List
C.FCH−2* & C.FCT−2
Foot Control, 230V
FOREDOM
The Foredom Electric Company
16 Stony Hill Rd., Bethel, CT 06801 • 203−792−8622
Fax: 203−796−7861 • www.foredom.net
}
Wiring Diagram
*C.FCH−2 is required for use with the latest
SR 230V motors produced since May 2006.
Form DN 12/10
Male Plug to
AC Power Source
Female Receptacle
to Motor
Wire
Connector
Wire Connector
2
4
3
1 5
6
Trigger Switch
BLK (BRN)
GRN/YLW
GRN
BRN (BLK)
BLU (WHT)
WHT (BLU)
GRN
(GRN/YLW)
Most Foot Controls have BLU(WHT) wires connected by a Wire Connector
as shown. Leave them connected, and connect only the BRN((BLK)
wires to Terminals 1 and 6 on the new Trigger Switch. Otherwise
connect all four wires to the Switch as indicated by the dotted wires.
3.
4.
Instructions for Removing
and Replacing Trigger Switch
Using flat blade of screwdriver inserted at Point A
between Cover (1) and Base (3), carefully pry Cover off.
Disconnect Foot Control from Motor and Wall Outlet.
Unscrew cover adjustment screw (5).
On older Switches, all the terminals will be push-in, spring clamp
type. On newer Switches, some terminals have screw fasteners.
To remove wires from the push-in terminals, insert 1.3mm [.05in]
approximate diameter pin or the blade of a jeweler's screwdriver
all the way into the terminal socket to release the spring clamp.
Grasp the tool and wire and pull them together out of the socket.
If you have difficulty removing the wires from the push-in terminals
and you have wire-cutting, stripping, and soldering tools, you can
cut the wires off where they exit from the terminals. To prepare
the cut wires for installation into the replacement Switch, strip
them back exactly 8.25 mm [5/16 in], then apply solder to the
stripped ends to fuse the strands together.
Remove Trigger Switch (2) from Base mounting bracket.
Connect Wires to New Trigger Switch as shown in the Wiring
Diagram. Push wires all the way in, so no bare wire is exposed.
On Screw Terminal 1, push wire lead all the way into the socket
then tighten the screw firmly. Push other wire leads all the way
into the designated terminals. Pull on all the wires, making sure
they are secure. Place Switch back into Base mounting bracket.
5.
8.
Snap cover (1) onto hinge posts on top of rear corners of base (3).
Insert adjustment screw (5) through washer (6) and into post
slot and threaded insert in cover (1). Tighten with screwdriver
until cover is just touching the trigger switch pushrod. Do not
tighten the screw further to avoid pressing the Switch Pushrod
into a permanently "on" position.
Position wires around adjustment screw post so wires will not
interfere with cover travel.
2.
1.
6.
7.
1
2
3
4
5
6
7
8
10
9
11
Point A