LED LENSER V2 User Manual

Led lenser, English, Deutsch

Advertising
background image

LED LENSER®*

*

English

*

Deutsch

*

Espanol

Wir freuen uns, dass Sie sich für ein Produkt aus unserem Hause entschieden haben.

Um sich mit Ihrem neuen Produkt vertraut zu machen, finden Sie hier eine Gebrauchsanleitung.
Artikel

LED LENSER

7736

Schwarz

7636

Schwarz Blister

7737

V² Silber

7637 V² Silber Blister

Version: 5.0
Batteriesatz:

3 x AAA/ LR03/ Micro (1,5 V DC)

(Art.-Nr. 7721)
Ein- und Ausschalten

Durch Betätigung der Druckschalters lässt sich die

ein- und ausschalten.

Wechsel der Batterien

Vor dem Wechseln der Batterien schalten Sie unbedingt die Lampe aus. Zum Wechseln der Batterien

schrauben Sie bitte die Lampe hinten auf.
a) Integrierter Batteriehalter

Der Batteriehalter ist mit der Endkappe verbunden. Ziehen Sie diese Einheit heraus und entnehmen Sie

die verbrauchten Batterien. Legen Sie die neuen Batterien entsprechend der Kennzeichnungen in den

Batteriehalter ein. Achten Sie darauf, die vorderen goldenen Kontakte nie kurzzuschließen. Halten Sie

diese Kontakte beim Batteriewechsel von allen metallischen oder feuchten Gegenständen fern.

Schieben Sie den Batteriehalter wieder ins Lampengehäuse. Schrauben Sie danach die Endkappe

wieder ein.
b) Einzelner Batteriehalter

Entnehmen Sie den Batteriehalter. Entfernen Sie die verbrauchten Batterien und entsorgen Sie diese

korrekt. Legen Sie die neuen Batterien entsprechend der Kennzeichnungen in den Batteriehalter ein.

Danach schieben Sie den Batteriehalter mit dem Pluspol voran wieder ins Lampengehäuse. Schrauben

Sie das Schaltergehäuse wieder ein.
Batterien

Nicht wieder aufladbare Batterien dürfen keinesfalls wieder aufgeladen werden. Verwenden Sie niemals

neue und gebrauchte Batterien zusammen. Verwenden Sie ausschließlich hochwertige Batterien

desselben Typs. Wechseln Sie immer alle Batterien auf einmal. Die Verwendung von Akkus und

hochstromfähigen Batterien ist wegen anderer elektrischer Werte nicht zugelassen. Falls Sie die Lampe

längere Zeit nicht verwenden wollen, entnehmen Sie unbedingt die Batterien, um Schäden zu

vermeiden. Leere Batterien müssen entnommen werden. Verbrauchte Batterien und Akkus sind

Sondermüll und müssen gemäß der nationalen Gesetzgebung entsorgt werden.
Zubehör

Das mitgelieferte Bändsel kann mit dem Miniatur-Schlüsselring an der Lampe befestigt werden.

Die Gürteltasche passt an Gürtel bis zu einer Breite von 50 mm(Koppel).
Achtung!

Beachten Sie beim Einlegen der Batterien unbedingt die Polaritätsmarkierungen! Wenn Sie den

Batteriehalter (Version b) entnommen haben, setzen Sie diesen mit dem positiven Anschluss (+)

zuerst ein. Andernfalls besteht eventuell die Gefahr, dass Batterien beschädigt werden und

explodieren.
Sicherheitshinweis

Richten Sie niemals absichtlich den Lichtstrahl in die eigenen oder in die Augen anderer Personen.

Falls ein Lichtstrahl in die Augen trifft, sind die Augen bewusst zu schließen und der Kopf aus dem

Lichtstrahl zu bewegen. Es dürfen keine optisch stark bündelnden Instrumente zur Betrachtung des

Lichtstrahls verwendet werden. Wenn jemand direkt in den Lichtstrahl blickt, kann die hohe Leuchtkraft

der Lampe zu Blenderscheinungen führen.

Bei gewerblicher Nutzung oder der Nutzung im Bereich der öffentlichen Hand ist der Benutzer

entsprechend der Vorschriften für Laserstrahlung zu unterweisen.

Estamos encantados de que hayan elegido uno de nuestros productos.

Para que se puedan familiarizar con este artículo a continuación les facilitamos unas breves

instrucciones de uso.
Artículo

LED LENSER

7736 V² Negro

7636 V² Negro Blister

7737 V² Plata

7637 V² Plata Blister
Version: 5.0
Pilas: 3 x AAA/LR03/Micro (1,5 V DC)

(Artículo no. 7721)
Encendido y apagado

Presionando el botón situado al final de la linterna V², esta se enciende o se apaga.
Cambio de Pilas

Antes de cambiar las pilas debe desenchufarse la linterna. Por favor, desenroscar la tapa al final de la

linterna.

a) Pilas conectadas al final de la tapa

Esta tapa final y el soporte de pilas está considerado como una única unidad. Tirar del soporte y extraer

las pilas usadas. Colocar adecuadamente las nuevas. Se deben evitar posibles cortacircuitos con los

contactos frontales. Tenga cuidado de no tocar los contactos frontales dorados con algún objeto de metal

o húmedo. Colocar el soporte de la batería dentro de la lámpara de nuevo. Cierre la lámpara enroscando

la tapa dentro de la rosca.

b) Pilas en formato independiente

Extraer el soporte de las pilas. Sacar las pilas y deshacerse de ellas de forma responsable.

Colocar adecuadamente las nuevas en el soporte. Insertar este dentro de la lámpara con el polo positivo

primero. Cerrar la lámpara enroscándolo hasta el final de la tapa.
Pilas

No intentar nunca recargar las pilas o usar las nuevas y las gastadas juntas. Cambiar siempre todas las

pilas usadas al mismo tiempo y usar unas de alta calidad y del mismo tipo. Usar sólo pilas de alta calidad

y del mismo tipo. Debido a los diferentes valores eléctricos el uso de acumuladores y las pilas de alta

calidad no está permitido. Si tienen la intención de no usar la lámpara durante un largo periodo de

tiempo, saque las pilas para prevenir posibles daños por goteo de las mismas. Las pilas usadas deben

ser retiradas. Las pilas usadas y acumuladores son desechos peligrosos y deben de ser tratados de

acuerdo con la legislación actual.
Accesorios

La cinta que se incluye puede ser anudada con el llavero pequeño. La funda adjunta se adapta a los

cinturones con un ancho máximo de 50mm (cinturón de trabajo).
Atención

Cuando se coloquen las nuevas pilas, seguir las marcas de polaridad en el soporte. Cuando se

reinsertan las pilas (versión B) en la linterna, debe hacerse con el polo positivo (+) primero.

Cuando se insertan mal las pilas o el soporte se podrían dañar las mismas.
Advertencia de Seguridad

Evitar enfocar a los ojos cuando la linterna esté encendida. Si sucede, cerrar los ojos y volver la cabeza.

No usar ningún instrumento con esta lámpara que pueda concentrar la luz. Cuando se mira

directamente a la lámpara la luz puede deslumbrar momentáneamente.

En caso de uso comercial, el usuario de la lámpara deberá seguir la legislación actual sobre salud y

seguridad y el resto de normativas en uso.

We are pleased that you have chosen one of our products. To get familiar with our product here is a

short instruction for use.
Item

LED LENSER

7736

black

7636

black Blister

7737

V² Silver

7637 V² Siver Blister

Version: 5.0
Batterypack:

3 x AAA/ LR03/ Micro (1.5 V DC)

(Item No. 7721)
Turn ON and OFF

By operating the push button at the end of the

you can switch the flashlight ON and OFF.

Change of batteries

Before changing the batteries you must switch off the flashlight. For changing the batteries please

unscrew the cap at the end of the flashlight.

a) battery pack connected to end caps

This end cap and the battery holder are one unit. Pull out this unit and take out the discharged

batteries. Fill in new batteries according to the plus and minus marks at the holder. You must not

cause a short circuit to the front contacts. Take care not to touch the front golden contacts with any

wet or metal object. Insert the battery holder into the flashlight housing again. Close the flashlight by

screwing the end cap into the thread.

b) single battery pack

Remove the battery holder. Take out the discharged batteries and dispose them properly. Fill in new

batteries according to the plus and minus marks at the holder. Then insert the battery holder into the

flashlight with the positive pole first. Close the flashlight by screwing on the end cap.
Batteries

Never try to recharge batteries or use fresh and used batteries together. Always change all batteries

at the same time and use high quality batteries and the same type only. Use only high quality

batteries of the same type. Because of different electrical values the use of accumulators and high

current batteries is not allowed. If you intend to not use this flashlight for a longer time, take the

batteries out to prevent damage by leaking batteries. Discharged batteries must be taken out. Used

batteries and accu-mulators are hazardous waste and must be disposed according to the national

legislation.
Accessories

The enclosed ribbon can be fastened at the end of the flashlight. The enclosed pocket fits to belts

with a width of max. 50 mm.(work belt).
Attention!

When inserting new batteries, follow the polarity marks at the battery housing. When you

reinsert the battery pack (versionb) into the flashlight, you must insert it with the positive (+)

terminal first. When inserting batteries or battery pack the wrong way this could damage the

batteries and might cause an explosion!
Security advice

You must not hit anybody at the eyes with the light out of this flashlight. If the light beam hits your

eyes, close the eyes and turn your head away. Do not use any magnifying instruments that

concentrate the light with this flashlight. When looking directly in this flashlight the light can

temporarily dazzle your eyes.

In case of commercial usage, the user of the flashlight must be instructed according to the national

regulations for health and safety and the rules of practice.

V

2

On/Off

An/ Aus

Encendido/Apagado

Marche/Arrêt

Aan/Uit

オン/オフ

켜짐

/꺼짐

开/关

Close

Schließen

Cerrar

Fermer

Sluiten

閉める

닫다

关闭

Open

Öffnen

Abrir

Ouvrir

Open

開ける

열다

打开

+ LED LENSER®* AAA -

+ LED LENSER®* AA

A -

+ LED LENSER®* AAA -

Advertising