Poly-Tex PT-30 - Manual (Page 13)

FIGURE 4
FIGURE 7
INTERMEDIATE
SECTIONS
FIGURE 2
PEAK
PURLIN
1. RAISE TWO FRAME SECTIONS, SLIDE INSIDE GROUND STAKES UNTIL
THEY REST ON THE SCREW INSTALLED IN THE GROUND STAKE
INSTALLATION, AND FASTEN TO GROUND STAKES WITH TWO 1/4"-14 x 1"
SELF DRILLING SCREWS. FIGURE 1
2. PLUMB FRAME SECTIONS AND ATTACH DIAGONAL BRACES USING
LONG SPEED HOOKS. FIGURE 2 NOTE: BRACE IS ATTACHED TO 3RD
FRAME SECTION ON 4' FRAME SPACING AND 2ND FRAME SECTION ON 6'
FRAME SPACING.
3. RAISE A THIRD FRAME SECTION, THEN ATTACH DIAGONAL BRACES
USING LONG SPEED HOOKS. ATTACH THE HP3340 PURLINS JUST BELOW
THE TRUSS CONNECTION USING CROSS CONNECTORS ON THE
INTERMEDIATE CONNECTIONS AND KH1000 ON ENDS. FIGURE 3 ATTACH
THE RIDGE PURLIN TO FRAME SECTIONS USING THE CROSS
CONNECTORS. FIGURE 3
4. USE PURLIN FASTENERS TO SECURE THE PURLIN TO THE END FRAME
SECTIONS ONLY. START WITH THE PLAIN END OF THE PURLIN FLUSH
WITH THE OUTSIDE OF THE FRAME SECTION. SECURE THE PURLIN
FASTENER WITH TWO #12-14 x 1" SELF-DRILLING SCREWS. SECURE THE
PURLIN TO THE PURLIN FASTENER USING ONE #12-14 x 1" SELF-DRILLING
SCREW AS SHOWN. FIGURE 4 ATTACH PURLINS TOGETHER WITH ONE
#12-14 x 1" SELF-DRILLING SCREW. FIGURE 5
TAP THE ROUND CAPS INTO THE END OF THE PURLINS WHEN DONE.
5. FOR PEAK PURLIN, USE END STRAP AND STOP TAB TO SECURE THE
PURLIN TO THE END FRAME SECTIONS ONLY. START WITH THE PLAIN
END OF THE PURLIN FLUSH WITH THE OUTSIDE OF THE FRAME SECTION.
SECURE THE PURLIN BY INSERTING THE STOP TAB INTO THE INSIDE OF
THE ROLL FORMED PURLIN (ONLY FITS ONE DIRECTION). SECURE THE
PURLIN TO THE END STRAP USING A 5/16" NUT AND LOCK WASHER
(STOP TAB IS SELF-TIGHTENING). DRIVE A #12-14 SELF-DRILLING SCREW
THROUGH THE HOLE ON THE STRAP AND INTO THE FRAME SECTION
( SEE FIGURE 6 ) ATTACH ADDITIONAL PURLINS TOGETHER WITH ONE
#12-14 x 1" SELF-DRILLING SCREW FOR EACH PURLIN.
6. FOR SECURING THE PEAK PURLIN TO INTERMEDIATE SECTIONS, TAKE
APART A UNI-CLAMP AND INSERT EACH CUT-OUT SIDE INTO THE PEAK
PURLIN ORIENTING THE BENT PARTS TO FIT AROUND THE FRAME
SECTION. RE-INSERT HARDWARE AND SECURE ( SEE FIGURE 7 ).
7. CONTINUE RAISING FRAME SECTIONS AND ATTACHING PURLINS UNTIL
DESIRED LENGTH OF STRUCTURE IS REACHED. ATTACH DIAGONAL
BRACES TO OPPOSITE END OF STRUCTURE AS MENTIONED ABOVE.
VERIFY THAT THE END FRAMES ARE PLUMB. CUT FINAL SECTIONS OF
PURLINS FLUSH WITH OUTSIDE OF LAST FRAME.
ALL COMPONENTS ATTACHED TO LONG SPEED HOOKS
MUST BE MOUNTED ON THE OUTSIDE OF THE TABS.
NEVER INSTALL COMPONENTS BETWEEN TABS.
IMPORTANT
FIGURE 5
FIGURE 1
FIGURE 6
END SECTIONS
ONLY
AD-130626
PURLIN
1/4"-14 x 1" SELF-
DRILLING SCREW
LEVELING
SCREW
1"
IMAGE IS 4ft ON CENTER
HOOP SPACING
#12-14 x 1" SELF
DRILLING SCREW
NB1804
KH1000
#12-14 x 1"
SELF-DRILLING
SCREW NB1804
RECT PLUG
FB2527
END STRAP
FT2106
ROLL FORM PURLIN
RR2109
STOP TAB
ST1021
PEAK
PURLIN
UNI-CLAMP
FT2108
LEVEL
INSERT RS5000
ROUND PLUGS
INTO ENDS (4)
LOCK WASHER
NB1862
HEX NUT
NB1872
SCREW
NB1809
FIGURE 3
HP3340
9'-8" TRUSS PURLIN
W/SWG-RED (2)