Qualcraft Edge Series SRL User Manual
Page 4
WARNING!
Do not alter or intentionally misuse this equipment. Consult with GFP when using this equipment in
combination with components or susbsystems other than those described here in this manual and or other
information. Use caution when using this equipment around moving machinery, electrical and chemical
hazards, and sharp edges.
WARNING!
I
I
f
f
i
i
n
n
s
s
p
p
e
e
c
c
t
t
i
i
o
o
n
n
r
r
e
e
v
v
e
e
a
a
l
l
s
s
a
a
n
n
u
u
n
n
s
s
a
a
f
f
e
e
o
o
r
r
d
d
e
e
f
f
e
e
c
c
t
t
i
i
v
v
e
e
c
c
o
o
n
n
d
d
i
i
t
t
i
i
o
o
n
n
,
,
r
r
e
e
m
m
o
o
v
v
e
e
t
t
h
h
e
e
p
p
r
r
o
o
d
d
u
u
c
c
t
t
f
f
r
r
o
o
m
m
s
s
e
e
r
r
v
v
i
i
c
c
e
e
a
a
n
n
d
d
s
s
e
e
n
n
d
d
p
p
r
r
o
o
d
d
u
u
c
c
t
t
b
b
a
a
c
c
k
k
t
t
o
o
G
G
u
u
a
a
r
r
d
d
i
i
a
a
n
n
F
F
a
a
l
l
l
l
P
P
r
r
o
o
t
t
e
e
c
c
t
t
i
i
o
o
n
n
o
o
r
r
a
a
G
G
F
F
P
P
a
a
u
u
t
t
h
h
o
o
r
r
i
i
z
z
e
e
d
d
s
s
e
e
r
r
v
v
i
i
c
c
e
e
c
c
e
e
n
n
t
t
e
e
r
r
.
.
PERSONAL FALL ARREST INFORMATION:
• Personal Fall Arrest System (PFAS): Personal fall arrest systems used with this equipment must meet applicable state,
federal, OSHA, and ANSI requirements. A full body harness must be worn when this equipment is used as a component of a
personal fall arrest system. As required by OSHA, the personal fall arrest system must be capable of arresting the user’s fall
with a maximum arresting force of 1,800 lbs., and limit the free fall to six feet or less.
OPERATION, USE and PLAN:
• Anchorage: The anchorage to which the SRL is attached must sustain static loads applied in the directions permitted by the
fall arrest system of at least 3,600lbs. with certification of a qualified person, or 5,000lbs. without certification. Refer to
OSHA and ANSI for specific definition. This device is to only be used by one person. When more than one personal fall
arrest system is attached to the same structure, the strength requirements stated above must be multiplied by the number of
personal fall arrest systems attached to the structure.
• Horizontal Systems and Tripods: In applications where an SRL is used in conjunction with a horizontal system or with a
tripod or davit arm, ensure the support structure and or the horizontal system components are compatible. Horizontal systems
must be designed and installed under the supervision of a qualified engineer.
• Anchorage Selection: Select a anchorage point capable of support at least 5,000 lbs. Additionally, select a location for
anchorage of the SRL that will avoid a free fall and swing fall hazards. To prevent an increased free fall distance, do not
work above the anchorage location.
• Free Fall: Personal fall arrest systems must be rigged so the potential free fall is never greater than six feet. Avoid slack in
the line and do not lengthen the SRL by connecting a lanyard or other snap hooks directly to the retractable. Do not use this
device at or below your feet. This will increase your free fall distance beyond the allowable limits set by OSHA and exceed
the capabilities of the SRL to safely arrest a free fall.
• Swing Falls: Swing fall will occur when the anchorage point is not directly over the head of the worker or directly above the
point where a fall occurs. The force of striking an object in a swing fall may cause serious injury up to and including death.
Minimize swing falls by working as directly below the anchorage point as possible. In all situations where a swing fall can
occur, the likelihood of an injury can occur. Please contact Guardian Fall Protection if you have questions on a particular
application involving one of our retractables.
• Fall Clearance: Ensure that there is always adequate clearance in the path of a fall to avoid striking an object or lower level.
A minimum of six feet from the working level to the lower level or nearest obstruction is recommended as long as the SRL is
attached directly over head of the worker and the worker is not in danger of injury as a result of a swing fall hazard.
• Sharp Edges: Unprotected and sharp edges can damage the lifeline. Please make sure to avoid working where this can
occur and provide protection where possible. A Guardian manufactured energy absorbing device can be added to aid in
reducing the impact forces on the entire device. For more information on this product, please contact Guardian Fall
Protection directly. No alterations to Guardian products is allowed.
INSPECTION OF SELF RETRACTING LIFELINES:
• Before each use of this equipment inspect it according to the following guidelines:
A formal inspection of fall protection products/components must be performed at least every six months by a competent
person other than the user. The frequency of formal inspections should be based on conditions of use or exposure. Record