Qualcraft Edge Series SRL User Manual
Page 5
WARNING!
CABLE INSPECTION:
When inspecting SRL’s that utilize cable lifelines, it is critical to look for the following damages and deterioration that will result
in malfunction of the unit and potentially unsafe conditions.
Crushing: The cable will often get crushed or bent while being used on a job site. Cable that is crushed or bent will damage
the retractable and thus the unit should be immediately taken out of service and returned to Guardian or an authorized repair
center.
Cutting: Movement over sharp edges or other objects while the cable is under tension can result in damaged strands and
broken wires. If, through inspection of the retractable lifeline prior to each use, it is found to have any broken strands,
immediately remove from service and return to Guardian or an authorized repair center.
Abrasion: Abrasion can result from normal wear. Particular attention must be paid to the outer wire strands as they will
appear to be flattened and or shiner than other parts of the cable. If, through inspection of the retractable lifeline prior to each
use, it is found have damage or deterioration from abrasion, immediately remove from service and return to Guardian or an
authorized repair center.
Kinking: Any deformation in the cable whereas the lifeline appears to be bent, requires the retractable to be immediately
removed from service and returned to Guardian or an authorized repair center.
Corrosion, Arc or Heat Damage: Extreme caution must be taken to avoid any potential damage as a result of using a
retractable within an environment where corrosive compounds, welding, or high heat may exist. Corrosive damage could
cause the cable to crack. Welding damage would result in fused wires and thus change the characteristics of the strength with
regards to the wire. If the retractable is used in these environments, the retractable lifeline needs to be closely examined for
damage. If you have any questions in terms of damage to the retractable or further explanation of the above information is
needed, please call 1-800-466-6385.
the inspection results in the inspection and maintenance log at the end of this manual. OSHA 1910.66, OSHA 1926.502 and
ANSI Z359.1 requires an inspection of equipment before each use.
• Annually: ANSI requires a formal inspection of the SRL be completed by a competent person other than the user at least
twice a year. More formal and frequent inspections maybe required based upon the severity and environmental conditions of
the workplace. Guardian Fall Protection Retractables, unless otherwise marked, are required to be recertified every two years
from the date of first use.
• After a Fall Arrest: Inspect the impact indicator on the snap hook of the SRL and look for an exposed red color band. Do
not attempt to reset the impact indicator. Remove the retractable from service immediately and return to Guardian or an
authorized repair center. If using a retractable with a webbed lifeline, then inspection of the shock pack is required. Remove
retractable from service if there are any deformation, elongation or other signs of the shock pack being torn or deployed. If
inspection reveals an unsafe condition, remove unit from service immediately and destroy, or contact an authorized service
center for repair.
Inspecting the SELF RETRACTING LIFELINES:
Step 1.
Inspect for loose screws and bent or damaged parts.
Step 2.
Inspect housing for distortion, cracks or other damage. Ensure the swivel eye is not damaged or distorted in
anyway. Make sure the swivel eye turns freely.
Step 3.
The lifeline must fully extend and retract without hesitation or creating a slack line condition.
Step 4.
Ensure the device locks up when lifeline is jerked sharply.
Step 5.
The labels must be present and fully legible with inspection log information completed.
Step 6.
Look for signs of corrosion on the entire unit.
Step 7.
Wire rope inspection must include identifying cuts, kinks, broken wires, bird-caging, corrosion, welding splatter,
chemical damage, or severely abraded areas. Check all thimbles etc…for excessive wear including cracks or
separation of metal components.
Step 8.
Webbed lifeline inspection must include identifying frayed strands, broken webbing, burns, cuts, and abrasions.
Inspect for excessive heat, paint build-up, soiling, rust, or chemical damage indicated by brown or discolored areas.
Step 9.
Inspect connecting hooks or carabiners for signs of damage, corrosion or excessive wear.
Step 10.
Record inspection results in the inspection and maintenance log found in this manual. Clearly check off month the
SRL was inspected on the label of the housing.