Qualcraft PRO-LINE Fixed Roof Bracket - Manual (Page 2)

ROOFING
PRODUCTS
PROFESSIONAL DUTY • FIXED PITCH ROOFING BRACKETS
60˚ 45˚ 90˚
INSTRUCTIONS FOR INSTALLA-
TION AND USE OF THE MODEL
#3503 8”x 60 DEGREE FIXED
PITCH ROOFING BRACKET
(FOR USE ON 21/12 PITCH
ROOFS): CAPACITY: One worker
per 8 feet of scaffolding plus 40
pounds of materials. GENERAL
REQUIREMENTS: When installed,
the platform support arm must be
set to match the pitch of the roof,
allowing for the installation of a
fully decked and level walk surface.
MOUNTING THE ROOF BRACKET:
1) All brackets shall be attached to
the roof with 20-penny nails. Use all
slots on mounting plate. 2) Position
bracket so that all nails penetrate
both the roof’s surface and the rafter
below. 3) Spacing between brackets
shall not exceed 8 feet. INSTALLING
PLATFORM: 1) wood platforms shall
not be less than 2 inches nominal
thickness and shall extend beyond
the support arm not less than 6
inches and not more than 12 inches.
2) Always use clear, straight-grained
wood free from knots or defects. 3)
If extended length platforms are re-
quired, use additional Roof Brackets
every 8 feet. 4) Secure to bracket by
nailing the platform to the bracket
using the hole provided in the plat-
form retainer. INSTRUCTIONS FOR
USE: 1) No more than one person
shall occupy any given 8 feet of a
Roofing Bracket Scaffold. 2) Always
use OSHA compliant fall arrest sys-
tem, guardrails, catch platforms or
other safety equipment as required
by Local, State or Federal OSHA
Regulations. 3) Roof Brackets are
intended for use by the experienced
tradesman. 4) OSHA Regulations re-
quire that employers provide training
in the use and care of this product.
CARE AND MAINTENANCE: 1) In-
spect all Roofing Brackets before
each use to be sure that there is
no damage or deformation, or de-
terioration from rusting. Discard if
necessary. 2) Do not throw or drop
from a building or onto a truck. 3) Do
not use if exposed to extreme heat
or cold. Discard at once. 4) Do not
use if wet or frozen.
INSTRUCTIONS FOR INSTALLA-
TION AND USE OF THE MODEL
#2503 & #3506 6”x 60 DEGREE,
#2504 & #3507 6”x 45 DEGREE,
#2505 & #3508 4”x 90 DEGREE
FIXED PITCH ROOFING BRACKET
(For use only as a material sup-
port): CAPACITY: 250 pounds of
roofing materials.. MOUNTING
THE ROOF BRACKET: 1) All brack-
ets shall be attached to the roof
with 20-penny nails. Use all slots on
mounting plate. 2) Position bracket
so that all nails penetrate both the
roof’s surface and the rafter below.
3) Spacing between brackets shall
not exceed 8 feet. INSTALLING
PLATFORM: 1) wood platforms shall
not be less than 2 inches nominal
thickness and shall extend beyond
the support arm not less than 6
inches and not more than 12 inches.
2) Always use clear, straight-grained
wood free from knots or defects. 3)
If extended length platforms are re-
quired, use additional Roof Brackets
every 8 feet. 4) Secure to bracket by
nailing the platform to the bracket
using the hole provided in the
platform retainer. INSTRUCTIONS
FOR USE: 1) Material supports are
not intended for use as a scaffold
or work platform.. 2) Always use
OSHA compliant fall arrest system,
guardrails, catch platforms or other
safety equipment as required by Lo-
cal, State or Federal OSHA Regula-
tions. 3) Roof Brackets are intended
for use by the experienced trades-
man. 4) OSHA Regulations require
that employers provide training in the
use and care of this product. CARE
AND MAINTENANCE: 1) Inspect all
Roofing Brackets before each use
to be sure that there is no damage
or deformation, or deterioration from
rusting. Discard if necessary. 2) Do
not throw or drop from a building
or onto a truck. 3) Do not use if
exposed to extreme heat or cold.
Discard at once. 4) Do not use if
wet or frozen.
INSTRUCTIONS FOR INSTALLA-
TION AND USE OF THE MODEL
#2501 & #3501 10”x 45 DEGREE,
MODEL #3504 8” x 45 DEGREE
PITCH ROOFING BRACKET (FOR
USE ON 12/12 PITCH ROOFS):
CAPACITY: One worker per 8 feet
of scaffolding plus 40 pounds of
materials. GENERAL REQUIRE-
MENTS: When installed, the plat-
form support arm must be set to
match the pitch of the roof, allowing
for the installation of a fully decked
and level walk surface. MOUNTING
THE ROOF BRACKET: 1) All brack-
ets shall be attached to the roof
with 20-penny nails. Use all slots on
mounting plate. 2) Position bracket
so that all nails penetrate both the
roof’s surface and the rafter below.
3) Spacing between brackets shall
not exceed 8 feet. INSTALLING
PLATFORM: 1) wood platforms shall
not be less than 2 inches nominal
thickness and shall extend beyond
the support arm not less than 6
inches and not more than 12 inches.
2) Always use clear, straight-grained
wood free from knots or defects. 3)
If extended length platforms are re-
quired, use additional Roof Brackets
every 8 feet. 4) Secure to bracket by
nailing the platform to the bracket
using the hole provided in the plat-
form retainer. INSTRUCTIONS FOR
USE: 1) No more than one person
shall occupy any given 8 feet of a
Roofing Bracket Scaffold. 2) Always
use OSHA compliant fall arrest sys-
tem, guardrails, catch platforms or
other safety equipment as required
by Local, State or Federal OSHA
Regulations. 3) Roof Brackets are
intended for use by the experienced
tradesman. 4) OSHA Regulations re-
quire that employers provide training
in the use and care of this product.
CARE AND MAINTENANCE: 1) In-
spect all Roofing Brackets before
each use to be sure that there is
no damage or deformation, or de-
terioration from rusting. Discard if
necessary. 2) Do not throw or drop
from a building or onto a truck. 3) Do
not use if exposed to extreme heat
or cold. Discard at once. 4) Do not
use if wet or frozen.
INSTRUCTIONS FOR INSTALLA-
TION AND USE OF THE MODEL
#2502 & #3505 6” X 90 DEGREE
& #3502 8”x 90 DEGREE FIXED
PITCH ROOFING BRACKET (For
use only as a slide guard or a
material support): CAPACITY: 250
pounds of materials. GENERAL
REQUIREMENTS: On roofs with
a 4/12 to 6/12 roof pitch, when in-
stalled as a slide guard, the scaffold
brackets should provide a platform
that is 90 degrees to the roof’s sur-
face at a point along the eave of the
roof. For roof slopes greater than 6/
12 up to 8/12 additional 90-degree
slide guards must be installed par-
allel to the first row no further than
every eight feet of roof slope. Ad-
ditional fall protection methods are
required on slopes 8/12 or greater.
When slope is greater than 4/12 and
the ground to eave height is greater
than 25 feet slide guards should not
be used. MOUNTING THE ROOF
BRACKET: 1) All brackets shall be
attached to the roof with 20-penny
nails. Use all slots on mounting plate.
2) Position bracket so that all nails
penetrate both the roof’s surface
and the rafter below. 3) Spacing
between brackets shall not exceed
8 feet. INSTALLING PLATFORM:
1) wood platforms shall not be
less than 2 inches nominal thick-
ness and shall extend beyond the
support arm not less than 6 inches
and not more than 12 inches. 2)
Always use clear, straight-grained
wood free from knots or defects.
3) If extended length platforms
are required, use additional Roof
Brackets every 8 feet. 4) Secure
to bracket by nailing the platform to
the bracket using the hole provided
in the platform retainer. INSTRUC-
TIONS FOR USE: 1) No more than
one person shall occupy any given
8 feet of a Roofing Bracket Scaffold.
2) Always use OSHA compliant fall
arrest system, guardrails, catch
platforms or other safety equip-
ment as required by Local, State
or Federal OSHA Regulations. 3)
Roof Brackets are intended for use
by the experienced tradesman. 4)
OSHA Regulations require that
employers provide training in the
use and care of this product. CARE
© Copyright 2003 • Qual-Craft ® Industries • 1551 Central Street
PO Box 559 • Stoughton, MA 02072
AND MAINTENANCE: 1) Inspect all
Roofing Brackets before each use
to be sure that there is no damage
or deformation, or deterioration from
rusting. Discard if necessary. 2) Do
not throw or drop from a building
or onto a truck. 3) Do not use if
exposed to extreme heat or cold.
Discard at once. 4) Do not use if
wet or frozen.
Customer Support and Ordering Information
781-344-1000 • www.qualcraft.com