Rapid-Air SMART MINI-SERVO GAG FEED - Manual (Page 10)

0
ProGramminG ProCedUre
(ContinUed)
F1, batch/total, on the
“RAMP/COUNTER” screen leads to:
EXIT
SET COUNTER vALUES
SET RESET
BATCh/ TOTAL
F1, set batch, on the “SET COUNTER
VALUES” screen leads to “BATCH
SET” screen discussed above in
SECTION 3.
F2, reset totals, on the “SET COUN-
TER VALUES” screen resets the total
counter to 000000.
F6, exit, will return to the “RAMP/
COUNTER” screen.
F2, speed/acc/dec, on the “RAMP/
COUNTER” screen leads to:
EXIT
ALTER PERCENTAGES
%ACC %DEC %SPEED
F6, exit, will return to the “RAMP/
COUNTER” screen.
F1, % acc, allows the acceleration
percentage to be altered with:
ENTER PERCENT OF ACC
MAX ACCEL = 000 %
MAXIMUM RATE (1 - 100) %
ENTER kEY TO EXIT
The enter key returns the display to
the “ALTER PERCENTAGES” screen.
F2, % dec, allows the deceleration
percentage to be altered with:
ENTER PERCENT OF DEC
MAX DECEL = 000 %
MAXIMUM RATE (1 - 100) %
ENTER kEY TO EXIT
The enter key returns the display
to the “ALTER PERCENTAGES”
screen.
F3, % speed, allows the speed per-
centage to be altered with:
ENTER PERCENT OF SPEED
MAX SPEED = 000 %
MAXIMUM RATE (1 - 100) %
ENTER kEY TO EXIT
The enter key returns the display
to the “ALTER PERCENTAGES”
screen.
SECTION 6 F6 - CYCLE ROLLER
F6, cycler roller, on the“MAIN
MENU” screen displays the following
screen.
EXIT
CYCLE FEED ROLLERS
OPEN CLOSE
ROLLER ROLLER
This allows the operator to manually
open and close the rollers.
SECTION 7 “.” - OUTPUTS DURATION
Pushing a “.”, outputs duration, while
in the “MAIN MENU” screen displays
the following screen:
OUTPUT DURATION
ENTER 0.000 FOR NONE
END FEED TIME=0.000
OUTPUTS TIME=0.000
This allows the operator to set
the duration of the END OF FEED
and SEQUENCE OUTPUTS. The
default duration of outputs is 250 mil-
liseconds. Please refer to the wiring
schematic for the locations of
the END OF FEED and SEQUENCE
OUTPUTS.
Depressing F3, auto mode, while on the
“AUTOMATIC MODE” screen will display:
EXIT
AUTO TOTAL = 000000
JOB # =00 LENGTh = 00.000
SPM = 000 SPEED = 000 %
The automatic cycle will continue
until the F6 key, exit, is pressed.
SECTION 4 F4 - JOB vALUES REvIEw
F4, job values, on the “MAIN MENU”
screen displays the following screen
until F6, exit, is pushed. The following
screen appears:
JOB # 00 SEQUENCE = 01
ENTER ThE SEQUENCE #
ThEN PUSh ThE ENTER kEY
Enter the sequence which is to be
reviewed and press
. The next
screen lists the current active job
number, sequence, the feed length,
number of repetitions, output se-
quence, speed, and whether the pilot
release is used:
JOB # 00 SEQUENCE = 01
FL = 00.000 REPEAT = 00
OUTPUT = 11111 PILOT = 0
SPEED = 003 F6 = EXIT
F6 exits to the MAIN MENU.
SECTION 5 F5 - RAMP/COUNTER
F5, ramp/counter, on the “MAIN
MENU” screen displays the following
screen:
EXIT
BATCh/ SPEED/
TOTAL ACC/DEC