Document Outline

• Series 982
• About This Manual
• Notes, Cautions and Warnings
• Technical Assistance
• Warranty and Returns
• Comments and Suggestions
• Table of Contents
• Chapter 1
  • Menu Overview
  • DIP Switches
  • Locations and Functions
  • Hardware Lockout/Battery Backup DIP Switch
  • External Power Supply
  • Universal Signal Input Type
• Chapter 2
  • Installing the Series 982
  • Wiring the Series 982
  • Wiring 0-20 and 4-20mA Process Inputs
  • Wiring Example
  • Wiring Notes
  • Input 1 Wiring
  • Input 2 Wiring
  • Event Input 1 Wiring
  • Output 1 Wiring
  • Output 2 Wiring
  • Output 3 Wiring
  • Output 4 Wiring
• Chapter 3
  • Display Loop
• Chapter 4
  • Navigating the Setup Menus
  • Reaching the Input Menu
    • Input Prompts
    • Decimal 1
    • Range Low 1 and Range High 1
    • Calibration Offset 1
    • RTD Calibration Curve 1
    • Software Filter 1
    • Input 2
    • Range Low 2
    • Range High 2
    • Learn Low
    • Learn High
    • Calibration Offset 2
    • Hunt
    • Slidewire Hysteresis
  • Reaching the Output
    • Output Prompts
    • Output 1
    • Process 1
    • Hysteresis 1
    • Output 2
    • Process 2
    • Hysteresis 2
    • Alarm 2
    • Latching 2
    • Silencing 2
    • Output 3
    • Alarm 3
    • Hysteresis 3
    • Latching 3
    • Silencing 3
    • Output 4
    • Alarm 4
    • Hysteresis 4
    • Latching 4
    • Silencing 4
    • Analog Output
    • Process 3
    • Retransmit Low Limit
    • Retransmit High Limit
    • Retransmit Calibration Offset
  • Reaching the Global Menu
    • Global Prompts
    • Celsius-Fahrenheit
    • Error Latching
    • Event Input 1
    • Event Input 2
    • Abort Set Point
    • Annunciator
    • Low Power Limit
    • High Power Limit
    • Auto-tune Set Point
    • Program Type
    • Guaranteed Soak Deviation
    • Power Outage
    • Idle Set Point
    • Profile Start
    • Lockout
  • Reaching the Communications Menu
    • Communications Prompts
    • Baud Rate
    • Data Bits and Parity
    • Protocol Type
    • Address
    • Interface Type
    • Interface Type
• Chapter 5
  • Reaching the System Menu
    • System Prompts
    • Event Input 1 Status
    • Event Input 2 Status
    • Event Output 3 Status
    • Event Output 4 Status
    • Alarm 2 Low
    • Alarm 2 High
    • Alarm 3 Low
    • Alarm 3 High
    • Alarm 4 Low
    • Alarm 4 High
    • Auto-tune
  • Reaching the PID Menus
    • PID Prompts
    • Output 1 Proportional Band [`Pb1 ]
    • Output 1 Reset
    • Output 1 Integral
    • Output 1 Rate
    • Output 1 Derivative
    • Output 1 Cycle Time
    • Output 2 Proportional Band
    • Output 2 Reset
    • Output 2 Integral
    • Output 2 Rate
    • Output 2 Derivative
    • Output 2 Cycle Time
    • Dead Band
• Chapter 6
  • Navigating the Factory Menus
  • Reaching the Diagnostics
    • Factory Ship Date
    • Software Revision
    • Serial Number
    • Ambient Temperature
    • Factory Use Only
    • Inputs 1 and 2 Module Types
    • Outputs 1, 2, 3 and 4 Module Types
    • Test Displays
    • Test Outputs
  • Reaching the Calibration Menu
    • Restore
    • Default
• Chapter 7
  • How to Program and Run the Series 982
  • Program Menu
  • Program Prompts
  • Running a Series 982 Profile
  • Resume a Profile
  • Pre-Run and Run Menus
  • Event Outputs
  • Guaranteed Soak Deviation
  • Programming a Ramping Profile
  • Editing Your Profile
  • Linking Profiles
  • The Waitfor Functions of the Soak Step
  • Master Step Chart
• Chapter 8
  • Auto-tuning
  • Manual Tuning
  • Changing the Output 3 Jumper
  • Using Alarms
  • Error Code E1 and E2 Messages
  • Error Code Actions
• Chapter 9
  • Burst Fire
  • Communications
  • Dead Band
  • Digital Events
  • Input Filter
  • Retransmit
  • Slidewire Feedback
• Warranty Warranty
• Returns
• Watlow Controls
• Shipping Claims
• Glossary, A-J
• Glossary, N-R
• Glossary, R-Z
• 982 Index
• Prompt Index
• Specifications
• Model Number
• Declaration of Conformity