KuulAire PACKA43 - Manual (Page 3)

Dampen a clean cloth with water and use it on the exterior
of the unit to remove any dust or dirt. Never use harsh
detergents, solvents, and corrosive cleaners to clean the unit.
When not in use, drain the water reservoir and store the unit
in an area where it is dry and out of sunlight.
MAINTENANCE:
Regular draining, at least once each week, will decrease the
water mineral build up and extend the life of the honey-comb
media pad. A damp cloth can be used to remove calcium build-
up inside and outside of the unit. The dust filter/cover can be
removed easily and can be cleaned weekly. The inside of the
water reservoir can be cleaned once or twice in a season to
maintain air quality.
DEEP CLEAN:
Remove screws holding the rear panel and remove the rear
panel by unhooking the tab located in the top of the rear panel.
Wash cooling pad with water and soft bristled brush to remove
debris and mineral build-up. Fill up the reservoir with fresh
water and drain. Repeat the procedure to remove debris and
mineral build-up in the reservoir.
WARNINGS AND SAFETY RULES
▲
!
LOCATION
PARTS DESCRIPTION
ELECTRICAL
ASSEMBLY INSTRUCTIONS
WARRANTY
CLEANING AND MAINTENANCE
TECHNICAL SPECIFICATIONS
TROUBLESHOOTING
REMOTE CONTROL
USE AND OPERATION
▲
!
WARNING: Unplug the unit from power
outlet prior to moving or servicing, or
filling or draining the water reservoir.
WARNINGS AND SAFETY RULES
▲
!
LOCATION
PARTS DESCRIPTION
ELECTRICAL
ASSEMBLY INSTRUCTIONS
WARRANTY
CLEANING AND MAINTENANCE
TECHNICAL SPECIFICATIONS
TROUBLESHOOTING
REMOTE CONTROL
USE AND OPERATION
▲
!
WARNINGS AND SAFETY RULES
▲
!
LOCATION
PARTS DESCRIPTION
ELECTRICAL
ASSEMBLY INSTRUCTIONS
WARRANTY
CLEANING AND MAINTENANCE
TECHNICAL SPECIFICATIONS
TROUBLESHOOTING
REMOTE CONTROL
USE AND OPERATION
▲
!
WARNINGS AND SAFETY RULES
▲
!
LOCATION
PARTS DESCRIPTION
ELECTRICAL
ASSEMBLY INSTRUCTIONS
WARRANTY
CLEANING AND MAINTENANCE
TECHNICAL SPECIFICATIONS
TROUBLESHOOTING
REMOTE CONTROL
USE AND OPERATION
▲
!
WARNINGS AND SAFETY RULES
▲
!
LOCATION
PARTS DESCRIPTION
ELECTRICAL
ASSEMBLY INSTRUCTIONS
WARRANTY
CLEANING AND MAINTENANCE
TECHNICAL SPECIFICATIONS
TROUBLESHOOTING
REMOTE CONTROL
USE AND OPERATION
▲
!
ON/OFF – start or turn off the unit
Timer – Turns on the timer
Cool – start water pump
Speed – Low/Medium/High
Swing – automatic swing of louvers
Cancel Timer – Cancels timer operation
Remote requires two (2) AAA batteries. Not included. Do not mix old and new batteries.
Do not mix alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium) batteries.
Do not dispose of batteries in fire. Batteries may explode or leak.
POWER
1. Plug the cord to a power outlet. The red power icon
will be illuminated with an audible sound. The unit is
in Standby mode.
2. Press POWER button to turn on the unit. Display will illuminate
and the POWER icon will turn green. When the POWER button is
pressed, the fan will start at HIGH, then switch to LOW speed. To
turn off the unit press the POWER button again.
SPEED - Press the SPEED button to select the desired fan
speed. The selected fan speed indicator LED light will
light up. Fan speed settings are 1( LOW) - 2 (MEDIUM)
- 3 (HIGH).
SWING: - Press the SWING button to direct the air
stream. The vertical louvers will begin to move
automatically from side to side. The indicator LED will
come on. To adjust the vertical direction of air flow, adjust the
horizontal louvers manually.
TIMER - The unit comes with a 8-hour timer function.
To set the timer, press the TIMER button to a desired
operation time. The selected time will be displayed. When
the selected time has elapsed, the unit will automatically
shut off.
COOL - To use the unit as an evaporative cooler,
press the COOL button. The pump will start and
distribute water to wet out the cellulose media
located in the rear of the unit. After approximately three
minutes, as the pad becomes saturated, the air from the
outlet should be cool.
LOW WATER ALARM FUNCTION - This unit is equipped with
a low water sensor alarm. When water in the reservoir is
below minimum level, you will hear audible beeps and COOL
LED indicator will flash continuously. At the same time the
power to the pump will be cut off to protect the life of the
pump. In order to disengage the alarm function, turn off and
unplug the unit from the power outlet, and fill the reservoir
with water above the minimum level. In order to turn off the
alarm function and continue to use it in FAN mode, press COOL
button again. If COOL button is pressed again without filling
the reservoir with water, low water alarm will go off again.
PACKA43 CONTROL PANEL
8/1/2012
(
COOL
CANCEL TIMER
PACKA43 CONTROL PANEL
8/1/2012
(
COOL
CANCEL TIMER
Water Reservoir Capacity 15 Liters/4 gallons
Dimensions (cm) 70.5 H x 40 W x 30 D
Dimensions (inches) 27.7 H x 15.7 W x 12.6 D
Product Weight 7.3 kg/16 lbs.
Model No. PACKA43
(110-120V 60Hz, 96W)
Model No. PACKA43-22050
(220-240V 50Hz, 115W)
Model No. PACKA43-22060
(220-240V 60Hz, 115W)