KEPCO BOP 1KW-MG Operator Manual, Firmware Ver.2.38 to 2.47 - Manual (Page 91)

BOP HIPWR 080709
3-27
3.3.9.5 VIEWING STORED WAVEFORMS
After observing the precautions of PAR. 3.3.9.1, press
@
from the power-up screen to access
the Saved Waveforms screen (Figure 3-9). Use Y or U or the encoder to highlight the name of
a previously saved waveform, then press
!
to view the Waveform Settings screen (see Figure
3-10). The lower half of the LCD shows a representation of the programmed waveform. The let-
ters along the vertical axis of the graph at the lower left side indicate whether the waveform is
programmed to operate in voltage or current mode. The message at the upper right indicates
the actual mode of the power supply while the waveform is being executed. The upper half pres-
ents the waveform name, positive and negative protection settings, the repetition count, fol-
lowed by a listing of segments. The type (square, sine, etc.), frequency, p-p amplitude, and
TABLE 3-9. SINE, TRIANGLE AND RAMP WAVEFORM FREQUENCY VS. POINTS
Frequency
(See Notes 1, 2, and 3) Total Points
Frequency
(See Notes 1, 2, and 3) Total Points
From To From To
0.01Hz 2.7Hz 3840 55.5Hz 66.5Hz 160
2.71Hz 3.6Hz 2880 66.6Hz 88.7Hz 120
3.71Hz 5.5Hz 1920 88.8Hz 118.3Hz 90
5.6Hz 8.3Hz 1280 118.4Hz 147.9Hz 72
8.4Hz 11.0Hz 960 148Hz 177.4Hz 60
11.1Hz 14.7Hz 720 177.5Hz 221.8Hz 48
14.8Hz 22.1Hz 480 221.9Hz 295.8Hz 36
22.2Hz 33.2Hz 320 295.81Hz 354.9Hz 30
33.3Hz 44.3Hz 240 355.9Hz 443.7Hz 24 (See Note 2)
44.4Hz 55.4Hz 192 443.8z 532Hz 20 (See Note 3)
NOTES: 1. As the frequency varies within the range, the time interval per point varies proportionately.
2. Sine and Triangle segments can not exceed 443Hz.
3. Ramp segments can not exceed 532Hz.
TABLE 3-10. SQUARE WAVEFORM FREQUENCY VS. POINTS
Frequency
(See Note 1) Total Points
Frequency
(See Notes 1) Total Points
From To From To
0.02Hz 1.8Hz 3840 43.51Hz 58.0Hz 120
1.81Hz 2.7Hz 2880 58.01Hz 72.5Hz 90
2.71Hz 4.0Hz 1920 72.51Hz 87.0Hz 72
4.01 5.4Hz 1280 87.01Hz 108.7Hz 60
5.41 7.2Hz 960 108.71Hz 145.0Hz 48
7.21Hz 10.8Hz 720 145.2.9Hz 174.0Hz 36
10.81 16.3Hz 480 174.1Hz 217.5Hz 30
16.31Hz 21.7Hz 320 217.6Hz 261.0Hz 24
21.71Hz 27.1Hz 240 261.1Hz 435.0Hz 20
27.11Hz 32.6Hz 192 435Hz 652.5Hz 12
55.5Hz 66.5Hz 160 653 1000 10
NOTE: 1. As the frequency varies within the range, the time interval per point varies proportionately.