NOSHOK 1000 Series Digital Pressure Gauges - Manual (Page 4)

3
 &$)-*$"+ "3"
&1*&2 
' &   &
% !"&
G& #" ' & 2  &
1 % !"&
%#"  %G (
*2/+"6
)
I$(
) @G& $&
 !!
D$ $G  %G (
2 , #> P   & /
2 1%
&"241*-( 1"-(&2
3. 
 D$ &#   D$
#& $% #" $HI%&
6/& .' /1&2241& =#% & J #J$G$%%I$
" & J #J$G$%%I$
5&1+."% +*,*3 ?'#E# 
!K  D$
&33&%
"3&1*"+2 %I$ " $" % 2 D$ %& " %% %& 5
 5 <

%I$ "  $! 
%I$ " $" %
 D$ #" ( %& " %% %&

!%I$ "  & "E ! & "# # (
1&2241& $.--&$3.1 Q <=?
#& $ #""&#$% #" $HI%&
3"#*+*36 /&1 6&"1 P  , #> I"$ $E$" #" & #"%
&,.16 <1
 ."#& J# &  J" ' "  " " D&&$ %/
1.(1",,*-(
,.%& "1",&3&12
) =%%'#$
) ?$
)
I&#!& 
%' & #EE & !
) %I$ " I" &
G& #" %&&D 
G& #" , #> %&&D 
#G& #" O4 ! " E&#$( %&
G& #" %&&D 
D$
=> = % &D 
++4,*-"3*.- .'
%*2/+"6
G& #"
.+3"(& 24//+6
) G$& " E
 K 2A 
 .
 !
/
/ %I$ " J & #" &# 7 3 4
 
" I " "#" "$ &(
(%&$% %

J & #" #E L$# G# "& " IGG$ $"  J I
0 psig to 30 psig through 0 psig to 10,000 psig,
others on request
Twofold, max 15,000 psig
Measuring ranges
a 750 psig stainless steel; AL 203; NBR,
Measuring cell ceramic
Measuring ranges
q 1500 psig only stainless steel,
measuring cell thin-film technology
5
Optional Tare Function
In this mode the positive deviation of the measured value from the
tared value (max. 20% of the measuring range) is constantly indica-
ted by the main display. The untared pressure value is always shown
on the bar graph display. Thus the Digital Gauge’s actual working
load can be read off even if the tare function is active. When the
tare function is active, a function indicator appears on the display.
There are two:
1) Select the tare function and set the value to be tared using
the keys . When set, the measured value to be tared is
backed up as tare. The main display and the auxiliary display then
show the value “0000” in the unpressurised state. Example: If a
value to be tared is set as 2 bar, the main display indicates 0 bar
in the unpressurised state.
2) Load the Digital Gauge with the pressure to be tared.
The current measured value appears in the main display
łAH@ of the main display. Select the tare function and then
operate both keys simultaneously . The current measured
value will be backed up as tare. The main display and the auxiliary
display are set to (0000).
Setting the tare value to (0000) resets the tare function in both
models.