TOHO ELECTRONICS TTM-10L - Manual (Page 3)

5.3 OTHER DISPLAY INDICATIONS
Shown whenever Input value exceeds the High limit of Display range, or the snapping of the Input line. ：
Shown whenever Input value exceeds the Low limit of Display range, or the snapping of the Input line at 4-20mA. ：
Shown for Memory error. Please contact us for repairing service. ：
Shown for A/D converter error. Please contact us for repairing service. ：
Shown for Auto-tuning error,Push any keys for resetting this display. ：
Shown when Parameter being changed during Key lock. ：
Shown during Auto-tuning. ：
5.4 INFORMATIONS FOR EACH PARAMETER
・MODE Display
Character Display conditions &
Descriptions Initial Value
Indications Remarks
Process Normal Display after the Ａ
ariable Input of Power V
Ｂ  （）∼ Shown on PID or Setting range:SV Limiter Low SV Limiter High
（） ON/OFF control. Setting
：1℃（ﾟＦ）  Value Setting unit :Thermocouple
:1／0.1℃（ﾟＦ） R.T.D.
：1／0.1／0.01 Current
Setting range Thermocouple Shown when Alarm Ｃ  ： ：-1999∼9999
Alarm R.T.D. Output s installed and ：-199∼999／-199.9∼999.9 i
Output Current set at Low Limit Alarm ：-1999∼9999／-199.9∼999.9／
Setting Output or High/Low Limit -19.99∼99.99 
Low Limit Setting unit Alarm Output. ：Same as that of B.Setting Value.
Setting range Shown when Alarm Ｄ  ：Same as that of C.Alarm Output
Alarm Output s installed and Setting Low Limit. i 
Output Setting unit set at High Limit Alarm ：Same as that of B.Setting Value.
Setting Output or High/Low Limit
High Limit Alarm Output.
Press UP/DOWN key more than 2 seconds for start/reset Shown on PI control. Ｅ  D
AT start of Auto-tuning,(AT)
: .   display Shown during AT
:    Shown without AT.
Shown alternatively during A T. NORMAL & : 
PARAMETER DISPLAY
Propor- Setting range Setting unit Shown on control. １  ：0.1∼200.0 ：0.1％  PID
tional Band
Integral Setting range Setting unit second Shown on control. ２  ：0∼3600 ：1 PID
Time Integral operation at OFF 
＝０
Deriva- Setting range Setting unit second Shown on control. ３  ：0∼3600 ：1 PID
tive Time Derivative operation OFF 
＝０ at
Output Setting range Setting unit second Shown on control. ４  ：1∼120 ：1 PID
 Proportional
Cycle
Setting range Thermocouple Shown on ON/OFF ５  ： ：0∼9999
Output R.T.D. control. ：0∼999／0.0∼999.9
：0∼9999／0.0∼999.9／ Sensitivity Current
0.00∼99.99 
. .. . Setting unit ：Same as that of above B.Setting Value
Setting range Same as that of above Displays at ON/OFF ６  ： C.Alarm Output
control. OFF point  Setting Low Limit.
B.Setting Value. position ： Setting unit Same as that of above
The Kind of Output needs ７   ＊＊※
Kinds of to be selected" "or" " ＊＊ Input Type ＊＊ Input Type  
  Ｐｔ１００ before purchase. INPUT/ K thermocouple therm-
J thermocouple ocouple OUTPUT   ＪＰｔ１００
E thermocouple he following Input types 4-20mA DC INPUT T  
T thermocouple are NOT selective.  
※ Output Type  R thermocouple
4-20mDC ←→   S thermocouple Relay contact output thermocouple
INPUT 4-20mADC   N thermocouple SSR Drive Output
W5Re/W26Re R.T.D←→4-20mADC  