Document Outline

• CONTENTS
• BEFORE YOU BEGIN
  • Parts List
  • About the Base and the Charger
  • Choosing the Best Location
  • About Caller ID with Call Waiting
  • About Call History
• INSTALLATION
  • Base Installation
    • Table/Desk
      • 1. Connect the corded handset to the base
      • 2. Connect the telephone line cord.
      • 3. Connect the power cord.
      • 4. Check for dial tone
    • Wall Mount
      • 1. Reverse the wedge under the base.
      • 2. Reverse cordless handset tab.
      • 3. Connect the telephone line cord to the jack labeled TEL LINE on the back of the base.
      • 4. Connect the power cord to the jack labeled DC IN 9V on the back of the base as shown.
      • 5. Replace the adapter on the base so the larger end is toward the bottom as shown.
      • 6. Connect the corded handset to the base.
      • 7. Connect the telephone line cord to the modular telephone jack.
      • 8. Plug the power cord into the electrical outlet.
      • 9. Mount the base on the wall.
      • 10. Check for dial tone.
  • Handset Charger Installation
    • 1. Connect the power cord.
    • 2. Install the handset battery.
    • 3. Charge the handset battery.
    • 4. Check for dial tone.
  • Belt Clip
  • Headset
• FEATURE SETUP
  • TELEPHONE OPERATION
    • AT THE BASE
      • Intercom
      • Base Ringer Volume Switch
      • Display Dial
      • Volume
      • Mute
      • Hold
      • Make,Answer, or End a Call
      • Redial/Pause
      • Flash
      • Other
        • Press to return to idle state
        • On steadily:
        • Flashing slowly:
        • Press to enter programming mode.
    • AT THE HANDSET
      • Answer a Call
      • Make a Call
      • Flash/ Call Waiting
      • Hold
      • Intercom
      • Handset Volume
      • End a Call
      • Exit
      • Cancel a page
      • Redial/Pause
      • Change Channel
      • Enter programming while not on a call.
  • Set the time and date displayed on handset screen
  • Set the phone for tone or pulse dialing (base only)
  • Set the language
  • Handset Ringer Style/Battery Save
  • Base Ringer Volume
  • TemporaryTone Dialing (Base or Handset)
  • Operating Range
  • Display Screen Messages (Handset and Base)
• TELEPHONE DIRECTORY AT THE BASE OR HANDSET
  • Store a Number/Name in the Directory
  • Edit a Number/Name Stored in the Directory
  • Delete a Number/Name Stored in the Directory
  • Dial a Number from the Directory
• CALLER ID OPERATION
  • About Call History
  • Review Call History
  • Delete Records from Call History
  • Dial a Displayed Number
  • Store a Call History Record in the Directory
  • DISPLAY SCREEN MESSAGES
  • Turn Off the Base NEW CALL Indicator
• ANSWERING SYSTEM OPERATION
  • AT THE BASE
    • Audible Indicators
    • Turn A n swering System On or Off
    • Set the Clock
    • About Mailboxes
    • About Announcements
    • RecordYour Announcement
    • Answering System Feature Setup
    • FEATURE SUMMARY
    • Listen to Messages
    • Adjust Playback Volume
    • Call Screening/ Intercept
    • Record a Memo
    • MESSAGE WINDOW DISPLAY
  • AT TOUCH TONE PHONE
    • Connect with the Answering System
    • Voice Menu
    • REMOTE ACCESS COMMANDS
• BATTERIES
  • Charge the Handset Battery Pack
  • Replacing the Handset Battery Pack
• IN CASE OF DIFFICULTY
  • TELEPHONE OPERATION
    • If the phone doesn’t work at all, check these items first:
    • If the above suggestions don’t solve the problem, try re-initializing the handset and base:
    • If you hear a two-beep signal when you try to use the handset:
    • If the phone does not ring when you receive a call:
    • If callers can not leave message in Mailbox 2 or 3:
    • If you hear noise or interference when using the phone:
    • If you hear other calls while using your phone
    • If you lose a call after changing channels:
    • If you are unable to operate special telephone services or other equipment requiring touch tone signal
    • If you have difficulty reading the base LCD
  • ANSWERING SYSTEM
    • If messages are incomplete
    • If you have difficulty hearing message
    • If the system does not answer after the correct number of rings:
    • If CL appears in the Messages Window:
    • If the system does not respond to commands from a remote touch tone phone:
    • If your outgoing announcement isn’t clear:
• DEFAULT SETTINGS
• IMAGES
  • BASE
  • BACK OF BASE
  • CORDLESS HANDSET