HP XP Command View Advanced Edition Software - Manual (Page 106)

All Storage/My Storage Operations 106
Table 8-2 Unallocated Group Information under All Storage/My Storage
Column Description
LDEV LDEV number. For LUSE, only a representative LDEV number is displayed. Select the link to display
the Detailed Information panel for the LDEV (refer to
Figure 7-7 ). You can use this item for filtering by
specifying a range.
Type Displays the LDEV type. This column displays only for StorageWorks XP12000/XP10000.
•
#AT = Internal volume to which an external volume is mapped, and the external volume consists
of SATA drives
•
#BD = Internal volume to which an external volume is mapped, and the external volume consists
of BD drives
•
#-
= Internal volume to which an external volume is mapped, and the drive type of the external
volume is not identified
•
- = LDEVs other than those above
SLPR Displays the SLPR number. This item is only displayed for a StorageWorks XP12000/XP10000 that
can use Disk/Cache Partition. If no SLPR is set, 0 is displayed. If a LUSE is used and different
SLPRs are set for the LDEVs making up the LUSE, Inconsistent is displayed.
CLPR Displays the CLPR number. This item is only displayed for a StorageWorks XP12000/XP10000 that
can use Disk/Cache Partition. If no CLPR is set, 0 is displayed. If a LUSE is used, Inconsistent is
displayed in either of the following cases:
• When different SLPRs are set for the LDEVs making up the LUSE
• When different CLPRs are set for the LDEVs making up the LUSE
If the LDEV is a Snapshot XP V-VOL, a blank is displayed.
EMU Type Emulation type for StorageWorks XP Disk Array. For LUSE, this item indicates the emulation type
and the number of LDEVs in the LUSE.
Capacity LDEV capacity. Values in GB and TB are rounded down to two decimal places. Values in MB are
rounded down to whole numbers. So, the value shown here may be less than the actual capacity.
For StorageWorks XP Disk Array, this field also displays the size of an intermediate HRX volume. For
more information on the HRX intermediate volume, refer to the documentation for the storage
subsystem you use.
Volume Attr Displays volume attributes for LUN Expansion (LUSE), Virtual LVI/LUN (CVS), Snapshot XP.
•
LUSE
= LUN Expansion or LUSE volume
•
CVS
= Volume created with the Virtual LVI/LUN (or CVS) function
•
LUSE (CVS)
= LUSE volume consisting of CVS volumes
•
V-VOL = V-volume used in Snapshot XP
•
POOL = Snapshot XP data pool volume
•
JNL-VOL = Continuous Access XP Journal journal volume
•
GUARD = LUN Security XP Extension volume
•
External
= External volume
•
IO Suppression
= Volume to which an external volume is mapped, and for which the host I/O
suppression mode is enabled
•
Cache Enable = Volume to which an external volume is mapped, and for which the I/O cache
mode is enabled
• None = Ordinary volume
Use this item for filtering. You can use a partial match specification as a condition for filtering.
CMD DEV Displays whether the LDEV is a command device (CMD DEV, or blank).
Copy Type Displays copy type:
•
BC = Business Copy XP
•
CA-XP(Sync) = Continuous Access XP Synchronous
•
CA-XP(Async) = Continuous Access XP Extension
•
CA-XP
= Continuous Access XP with unidentifiable synchronous mode*
•
Snapshot
= Snapshot XP
•
CA-XP(Jrnl)
= Continuous Access XP Journal
•
Unpaired = unpaired
• None = pair status unknown
Use this item for filtering. You can use a partial match specification as a condition for filtering.
Copy Role Copy role: P-VOL, S-VOL, or Blank = ordinary volume
This item can be used for filtering. You can use a partial match specification as a condition for
filtering.