Failed auto migration plan messages – HP XP P9000 Auto LUN Software User Manual
Page 36
Table 19 Stopped auto migration plan messages (continued)
Description
Message
The disk usage rate of the parity group including the source
volume is over the specified limit. Or, the disk usage rate
The auto migration plan (LDKC:CU:LDEV->LDKC:CU:LDEV)
was stopped. The usage rate of the source volume is over
is unknown. If applicable, increase the Max. disk utilization
the specified Max. disk utilization value, or the usage rate
is unknown.
value in the Auto Plan Parameters section of the Auto Plan
window and reinstate the auto migration plan.
The migration plan failed due to an error indicated by the
error code. '5205' is the part code for Auto LUN and
The auto migration plan (LDKC:CU:LDEV->LDKC:CU:LDEV)
was stopped. The migration failed. Error code:
5205-NNNN.
'NNNN' represents the error number. For information on
the error and recommended action, see the HP XP P9000
Remote Web Console Messages document.
The size of the source volume is different from that of the
target volume. The volume configuration might have been
changed after the creation of the auto migration plan.
The auto migration plan (LDKC:CU:LDEV->LDKC:CU:LDEV)
was stopped. There is a volume size mismatch between
source and target volumes.
The emulation type of the specified target volume is not
supported. The volume configuration might have been
changed after the creation of the auto migration plan.
The auto migration plan (LDKC:CU:LDEV->LDKC:CU:LDEV)
was stopped. Unsupported emulation type.
The check of the disk usage rate of the parity group
including the source volume ended abnormally. Contact
the service engineer for information on resolving this issue.
The auto migration plan (LDKC:CU:LDEV->LDKC:CU:LDEV)
was stopped. Failed to check the usage rate of the source
volume.
The check of the target volume ended abnormally. Contact
the service engineer for information on resolving this issue.
The auto migration plan (LDKC:CU:LDEV->LDKC:CU:LDEV)
was stopped. Failed to check the target volume.
An unknown error occurred while checking the target
volume. Contact the service engineer for information on
resolving this issue.
The auto migration plan (LDKC:CU:LDEV->LDKC:CU:LDEV)
was stopped. An unknown error occurred in checking
target volumes.
The encryption status of the source volume is different from
that of the target volume. The volume configuration might
The auto migration plan (LDKC:CU:LDEV->LDKC:CU:LDEV)
was stopped. There is an encryption status mismatch
between source and target volumes.
have been changed after the creation of the auto migration
plan.
Failed auto migration plan messages
lists messages related to failed auto migration plans.
The Class X and Group X-X variables in the Message column represent the HDD class and parity
group where the error occurred.
Table 20 Failed auto migration plan messages
Description
Message
Auto LUN could not specify a proper target volume for
creating an auto migration plan.
Failed to create auto migration plans. Failed to specify a
proper target volume.
Error location: Class X Group X-X
There are insufficient data for creating auto migration
plans. Check the Sampling Term and Number of Sampling
Failed to create auto migration plans. Insufficient statistics
data in the sampling term.
Points settings in the Auto Plan window to see if monitoring
Error location: Class X Group X-X
data is being properly acquired. Make any necessary
adjustments and attempt to collect the data again.
There is an insufficient amount of reserved volumes for
creating auto migration plans. If Auto LUN failed to obtain
Failed to create auto migration plans. Insufficient reserved
volumes.
the specified information, check the Reserve volumes in the
Attribute window.
Error location: Class X Group X-X
Auto LUN failed to obtain specified information or statistics
which are required for creating auto migration plans.
Failed to create auto migration plans. Failed to obtain
XXXXXXXXXX.
'XXXXXXXXXX' represents the information or statistics that
Error location: Class X Group X-X
36
Auto LUN monitoring