Dimensions and specifications (in inches), Grounding the fresh-food refrigerator, 3/4” overlay panel dimensions – GE ZIFS240PLSS User Manual

Page 2

Advertising
background image

Specification Revised 7/05

120032

ZIFI240PII – GE Monogram Fresh-Food Refrigerator Module

(Custom panel required) )

ZIFS240PSS – GE Monogram Fresh-Food Refrigerator Module

(Stainless steel)

Dimensions and Specifications (in inches)

34-1/2" - 35"

24" Min.

47-1/2" Min.

1-1/2"

Locate Outlets

9"

Max.

10-1/2"

1-1/2"

9"

Max.

10-1/2"

24"

For a complete food storage center, install two Monogram refrigeration

modules side-by-side.
Note: Reversible door swing on wine chillers/reserves and beverage

centers only. See below for combination cutout dimensions.
Important Note: Products must operate from separate, properly

grounded receptacles.

Grounding the Fresh-Food Refrigerator

IMPORTANT – (Please read carefully)
FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE

PROPERLY GROUNDED.
The power cord of this appliance is equipped with a 3-prong

(grounding) plug which mates with a standard 3-prong (grounding)

wall receptacle to minimize the possibility of electric shock hazard

from this appliance.
Have the wall outlet and circuit checked by a qualified electrician to

make sure the outlet is properly grounded.
When a standard 2-prong wall outlet is encountered, it is your

personal responsibility and obligation to have it replaced with a

properly grounded 3-prong wall out.
DO NOT, UNDER ANY CIRCUMSTANCES,

CUT OR REMOVE THE THIRD (GROUND)

PRONG FROM THE POWER CORD.
DO NOT USE AN ADAPTER PLUG TO CONNECT THE

REFRIGERATOR TO A 2-PRONG OUTLET.
DO NOT USE AN EXTENSION CORD WITH THIS APPLIANCE.

Note: Additional cutout width may be required for models with

custom panels.

3/4” Overlay Panel Dimensions

Model ZIFI240PII requires customer-provided

overlay door panel.
• The overlay panel must be secured to a 1/4"

thick backer panel which slides into the trim.

A .10" thick spacer panel must be placed

between the custom and backer panel.

• A custom handle of your choice, supplied by

your cabinet maker, must be installed on the

overlay panel.

Overlay

Panel

1/4"

Backer

Panel

Door

.10 Inch

Spacer

For answers to your Monogram,

®

GE Profile

or

GE

®

appliance questions, visit our website at

GEAppliances.com or call GE Answer Center

®

service, 800.626.2000.

Listed by

Underwriters

Laboratories

3/4" Overlay Panel Dimensions (in inches)

A (Width) B (Height)

1/4" Backer

23-3/16"

29-9/16"

0.10" Spacer

22-1/2"

29-1/16"

3/4" Overlay

23-5/8"

30"

NOTE: Max. assembled drawer panel weight

is 25 lbs.

Assemble overlay panels with glue

and screws.
• Center spacer panel on the backer panel,

left to right and top to bottom. Secure

the panels with glue.

• Center the spacer/backer panel on

the overlay panel. Secure with glue

and screws. Countersink screws into

the backer panel.

Spacer Panel

Backer Panel

Overlay Panel

Use a 3/4" router bit to cut a notch into the back side

of the assembled panel to allow for hinge clearance.

A

B

3/4" Deep

7/8" Wide

3/8" toward

the front side

Back Side

of Panel

R

Advertising
This manual is related to the following products: