GE ZV755SPSS - Manual (Page 2)

monogram.com
45
c
him
n
e
y
h
ood
s
p
ro
fe
ssi
o
n
al
h
ood
s
c
u
sto
m
ho
o
d
i
n
se
rt
s
te
le
sc
o
pi
c
d
ow
n
d
ra
ft
v
e
n
ts
Advance planning for chimney hoods—wall-mount
Wall-mount hoods
Chimney vent hoods are available in 30" and 36" widths. All
models are supplied with a two-piece stainless steel duct cover
to conceal the ductwork running from the top of the hood to
the ceiling.
• The installation height should be determined in advance.
If necessary, accessories for height adjustment should be
ordered with the vent hood and be on-site at the time of
installation.
• Review the following chart to determine the need for an
accessory duct cover.
Duct cover accessories for vented installations
Ceiling
height
ZV830 ZV750/
755
ZV950 ZV800 ZV900
8' Included Included Included Included up to 9'5"
Up to 9' Included Included Included Included up to 9'5"
Up to 10' Included ZX7510SPSS Included Included ZX90010*
10' to 12' ZX83012 — — — —
10' to 14' — — ZX14SDSS — —
*ZX90010 for 9'6" up to 10'5"
Structural support
These vent hoods are heavy. Adequate structural support
must be provided. Hoods must be secured to vertical studs
in the wall or to horizontal supports.
• It is strongly recommended that the vent hood and duct
cover(s) if used, be on-site before final framing and wall
finishing. This will help to accurately locate the ductwork
and electrical service.
• Final installation will be much easier if the hood is installed
before the range or cooktop below.
• Mounting templates are provided with the installation
instructions to help accurately position the hood above the
cooking surface.
Electrical requirements
These vent hoods must be supplied with 120V, 60Hz, and
connected to an individual, properly grounded branch circuit
protected by a 15- or 20-amp circuit breaker or time-delay fuse.
Ductwork planning
• Plan the shortest and straightest route for venting exhaust
to the outdoors.
• Use metal ductwork only.
• Install a wall cap or roof cap with damper at the exterior
opening. Order the wall or roof cap and any transition
needed in advance.
Ductwork for ZV830SMSS
This vent hood must use 8" round duct with a maximum
equivalent length of 100 feet for any duct configuration.
Refer to the duct fittings chart in the installation instructions.
Decorative duct covers
This vent hood is supplied with a two-piece decorative duct
cover that will reach an 8' to 10' ceiling. ZX83012 can be
ordered to reach 10' to 12' ceiling heights. All duct covers are
reversible for recirculating operation.
Ductwork for ZV750/755SPSS
This vent hood must use 6" round duct with a maximum
equivalent length of 100 feet for any duct configuration.
Refer to the duct fittings chart in the installation
instructions.
Decorative duct covers
This vent hood is supplied with a two-piece decorative duct
cover that will reach an 8' to 9' ceiling. ZX7510SPSS can be
ordered to reach 9' to 10' ceiling heights.
Recirculating installation for ZV750/755SPSS
The ZV750/755 hood is designed to be
vented to the outside, but can easily
be converted for recirculating operation.
Recirculating kits are included for
this hood. These kits include charcoal
filters, an air deflector that fits over the
exhaust outlet and a vented decorative
duct cover. Kits are sized for
ceiling height.
Ductwork for ZV800SJSS
This vent hood must use 6" round duct with a maximum
equivalent length of 100 feet for any duct configuration.
Refer to the duct fittings chart in the installation
instructions.
Decorative duct covers
This vent hood is supplied with a two-piece decorative duct
cover that will reach an 8' to 10' ceiling. The duct covers are
reversible for recirculating operation.
Ductwork for ZV900SLSS
This vent hood must use 8" round duct with a maximum
equivalent length of 100 feet for any duct configuration. Refer
to the duct fittings chart in the installation instructions.
Decorative duct covers
This vent hood is supplied with a two-piece decorative duct
cover to reach an 8' to 9'5" ceiling. ZX90010 can be ordered to
reach 9'6" to 10'5" ceiling heights. All duct covers are reversible
for recirculating operation.
Ductwork for ZV950SDSS
This vent hood must use 8" round duct with a maximum
equivalent length of 100 feet for any duct configuration.
Decorative duct covers
This vent hood is supplied with a two-piece decorative duct
cover that will reach an 8' to 10' ceiling. An optional accessory,
ZX14SDSS, can be ordered to reach 10' to 14' ceiling heights.
For vented operation only.
605Dia145