GE ZISS360NXSS - Manual (Page 2)

STANDARD INSTALLATION
ANTI-TIP BRACKET
Product Specification Created 3/14
FRONT VIEW SIDE VIEW
W
24" (61.0)
2"
(5.1)
4"
(10.2) 7/16" (1.1)
Trim overlap
3 1/2"
(8.9)
E
WATER
35 1/2"
(90.2)
12" (30.5)
*83 1/2" min
*84 1/2" max
(212.1-214.6)
*Trim will overlap
additional 7/16"
3 1/2"
(8.9)
75"
(190.5 )
From floor
to bottom
of electrical
area
6"
(15.2)
5"
(12.7)
5"
(12.7)
5"
(12.7)
ZISS360NXSS
SIDE VIEW INSTALLED
WITH WOODEN WALL STUDS
AND NO SOFFIT
SIDE VIEW INSTALLED
UNDER SOFFIT
SOFFIT
*84"
(213.4)
*Or installation
height from floor
2" x 4"
Cut to 35" Length
Screws mounted
into vertical wall
studs
FRONT VIEW INSTALLED
WITH METAL WALL STUDS
AND NO SOFFIT
Top Case Trim
3/4"
Min.
Side View Top
Case Trim
Install Screws
Through Trim and Into
3/4" Min. Wood Brace
FRONT VIEW SIDE VIEW
W
24" (61.0)
2"
(5.1)
4"
(10.2) 7/16"
(1.1)
Trim overlap
3 1/2"
(8.9)
E
WATER
35 1/2"
(90.2)
12"
(30.5)
*83 1/2" min
*84 1/2" max
(212.1-214.6)
*Trim will overlap
additional 7/16"
3 1/2"
(8.9)
75"
(190.5 )
From floor
to bottom
of electrical
area
6"
(15.2)
5"
(12.7)
5"
(12.7)
5"
(12.7)
ZISS360NXSS
SIDE VIEW INSTALLED
WITH WOODEN WALL STUDS
AND NO SOFFIT
SIDE VIEW INSTALLED
UNDER SOFFIT
SOFFIT
*84"
(213.4)
*Or installation
height from floor
2" x 4"
Cut to 35" Length
Screws mounted
into vertical wall
studs
FRONT VIEW INSTALLED
WITH METAL WALL STUDS
AND NO SOFFIT
Top Case Trim
3/4"
Min.
Side View Top
Case Trim
Install Screws
Through Trim and Into
3/4" Min. Wood Brace
A
B
D
E
C
ZISS360NXSS GE Monogram ® 36" Built-In Side-by-Side Refrigerator
The refrigerator will project forward,
slightly beyond adjacent cabinetry.
A Mounting the junction
box in this location will
also allow for front
accessability through
access panel.
B Water supply area.
WARNING:
The refrigerator is top
heavy and must be secured
to prevent the possibility of
tipping forward. Failure to
do so may result in death
or serious injury.
The information below is
for cabinet design only.
When installing the anti-
tip system you must use
the product installation
instructions.
Determine your installation
construction and required
anti-tip configuration:
C Installed Under Soffit
After installing unit into
installation opening,
raise grille panel and
screw metal case sides to
adjacent cabinet. When
installed under a soffit,
the soffit cannot exeed 24”
deep. The top case trim
overlaps the bottom of the
soffit.
D Wooden Wall Studs and
No Soffit
• Cut a 2” x 4” block and
secure to brackets
provided.
• Secure brackets to back
wall of opening at 84” or
your installation height
from the floor.
E Metal Wall Studs and
No Soffit
This method requires
securely fastened cabinets
on both sides and a ¾”
minimum wood brace
above unit, with it’s front
surface 24” from back wall.
• After installing unit into
opening, raise grille panel
and attach metal case
top trim to ¾” minimum
wood brace.
• The brace spanning
the enclosure must be
securely fastened to
cabinets on both sides.
See Installation
Instructions for detailed
instructions.
NOTES