GE ZIC360NXRH User Manual

696dia8, Zic360nx, Ge monogram

Advertising
background image

For answers to your Monogram,

®

GE Profile

or

GE

®

appliance questions, visit our website at

ge.com or call GE Answer Center

®

service,

800.626.2000.

110112

Specification Created 6/08

Listed by

Underwriters

Laboratories

ZIC360NX

GE Monogram

®

36" Built-In Bottom-Freezer Refrigerator

Dimensions and Installation Information (in inches)
The Installation Space
The finished cutout width
must be 35-1/2".

Product Dimensions

* Shipping Height. The

refrigerator can be adjusted to

fit into a cutout that is 83-1/2"

min. to 84-1/2" max. height. The

top case trim at the front is 1/2"

higher and will overlap upper

cabinetry or soffit. Use leveling

legs and wheels for a maximum

1" height adjustment.

The cutout depth must be 24"

The refrigerator will project forward, slightly beyond adjacent

cabinetry, depending on your installation.
The cutout depth beneath a soffit

When installed beneath a soffit, the soffit cannot exceed the

24" installation depth shown. The top case trim overlaps the

bottom of the soffit.
Electrical

A 115V, 60Hz., 15 or 20 amp power supply is required. An

individual properly grounded branch circuit or circuit breaker

is recommended. Install a properly grounded 3-prong

electrical receptacle recessed into the back wall. Electrical

must be located on rear wall as shown.
Note: GFI (ground fault interrupter) is not recommended.
Water Line

All models are equipped with an automatic icemaker. The

water line can enter the opening through the floor or back

wall. Route GE SmartConnect

Kit or 1/4" O.D. copper tubing

between the cold water line and the water connection

location at the front of the refrigerator. The installation of an

easily accessible shut-off valve in the water line is required.

696Dia7

6"

Wall View

Electrical

Area

84-1/2" max

83-1/2" min

Finished

Opening

75" From

Floor to Bottom

of Electrical

Area

10"

5"

3 1/2"

5"

3 1/2"

24" Cutout Depth

35-1/2"

Finished Width

2-5/16"

Note: Icemaker

water connection

is at the front.

Cold Water

Supply

605Dia20

25"

Min. to

Wall

130

°

130

° Door Swing

23-7/8"

Behind

Frame

36-3/4"

605Dia21

90

°

90

° Door Swing

4" Min. to Wall

5" Min. for Professional Models

2-5/16"

75" From

Floor to Bottom

of Electrical

Area

84-1/2" max

83-1/2" min

Finished

Opening

71-1/2" Finished Width

Electrical

5"

3-1/2"

24" Cutout

Depth

Water Supply

Wall View

696Dia8

24-3/16"

26"

6"

10"

10"

Water Supply

26"

5"

3-1/2"

Door Swing Clearances
The installation must allow for clearances to adjacent walls or
cabinets. These refrigerators are equipped with a 2-position
door stop. The factory-set 130° door swing can be adjusted to
90° if clearance to adjacent cabinets or walls is restricted.

Allow 25" minimum clearances for a full 130° door swing.
Allow 15" for pan removal.
• 4" minimum clearance is required when the door swing is

adjusted to 90°. If the 90° door stop position is used, pan
access is maintained, but pan removal is restricted.

• See door swing illustrations to determine interaction with

adjacent cabinets or countertops.

ZUG2, ZUGSS2 Unified Grille Panel Kit
• If you are installing two refrigerators side by side, the

installation space must be 71-1/2" wide.

Note: Additional cutout width may be required when side
panels are used. Add side panel thickness to the finished
cutout to calculate rough-in width.
• The water and electrical locations for each product must

be located as shown.

• A separate 115V, 60Hz., 15 or 20 amp power supply is

recommended for each product.

429Dia9

*84" From

Floor to

Top Frame

35"

Case Width

*83-1/2"

at

Rear

Case Depth:

25-3/8" Framed Models

25-3/4" Stainless Steel Models

Depth Including Handles:

26-7/8" Framed Models

27-3/4" Stainless Steel Models

28-11/16" Professional Models

36"

Frame to Frame Width

Advertising
This manual is related to the following products: