Limited warranty – Rocky Mountain Radar KAT-MATRIX User Manual

Page 2

Advertising

MATRIX

LIMITED WARRANTY

MATRIX

OPERATION

Six push buttons control operation. The MODE button cycles
through the operational modes, 1⁄4 MILE, 0 TO 60, and G-
Force. The MEMORY button selects memory locations
containing results of tests. STORE button causes the current
test results to overwrite the location of a selected memory
location. The UP and DOWN buttons scroll data from memory
or test results and change setup data. The START button zeros
the three-axis accelerometer readings.

Your car must be stopped before you perform a test.

0 to 60

Pressing the MODE key until the display shows:

The test begins as soon as the vehicle starts moving and the
display shows the elapsed time until 60 MPH is reached.
Then it shows the time to reach 60 MPH

MODE BUTTON

- Press MODE button to power the unit on. Press two (2)
seconds to power the unit off.

- You can choose the mode you want by pressing this MODE
button when that mode is displayed: 1/4Mile, 0-60Mile, G-
Force.

START BUTTON

Press START button at each mode to perform testing. Start
when the display is ready.

MEMORY BUTTON

Press the MEMORY button any time a test is not running until
the desired memory location is shown in the display. Press the
UP and DOWN keys to scroll through the test results. Press
START or MODE buttons to exit the MEMORY mode.

Press MEMORY button for three (3) seconds to enter set-up
mode.

STORE BUTTON

At the end of any test, press the MEMORY button until the
desired memory location, MEM 1, MEM 2 or MEM 3 shows in
the display. Then press STORE button to overwrite the display
with the new information. The results of the test are stored in
memory.

UP AND DOWN BUTTONS

Press UP or DOWN buttons to review data from last tests.

Press DOWN button for five (5) seconds to enter Factory Reset
Mode.

FACTORY RESET

Press DOWN button for five (5) seconds to enter Factory Reset
mode and press STORE button to reset all data to factory
default.

- Clear all memories
- Set-up items
- Calibration data

Press MEMORY button to cancel the factory reset.

CALIBRATION

Calibration is performed automatically when you press START
button

MEMORY

Setup and test results are stored in memory so data is retained
when power is OFF or batteries changed.

DISPLAY BACKLIGHT

The backlight is turned on when any button is pushed and
remains on for 1 minute unless a test is being run, then it stays
on until 1 minute after the test is completed. Each button push
resets the 1 minute timer.

AUTO POWER OFF

The Matrix will automatically shut off the power after one hour if
no buttons are pressed.

The Matrix will give warning beep before power off. Press any
buttons to cancel auto power off.

Low Battery Warning

The Matrix will give low battery warning from the moment when
there is about two hours of remaining battery life.

ERROR MESSAGES

ERROR 1: Speed decrease during testing
ERROR 2: Tilted more than 30 degrees during calibration
ERROR 3: Vibration during calibration

The manufacturer warrants your Matrix against all defects in
materials and workmanship for a period of one (1) year from
the date of the original purchase, subject to the following terms
and conditions: The sole responsibility of the manufacturer
under this Warranty is limited to either repair or, at the option of
the manufacturer, replacement of the Matrix. There are no
expressed or implied warranties, including those of fitness for a
particular purpose of merchantability, which extend beyond the
face hereof. Some states do not allow limitations on how long
an implied warranty lasts, so the above limitations may not
apply to you.

Pressing the UP or DOWN button once causes the display to
show average horsepower between the two speeds chosen in
setup.

Pressing the UP or DOWN button again shows the peak
horsepower reached during the test.

1⁄4 MILE

Press the MODE button until the display shows:

The test begins as soon as the vehicle starts moving and the
display shows current elapsed time. At the end of 1⁄4 mile, the
speed reached is displayed.

Pressing the UP or DOWN button causes the display to show
the time for 1⁄4 mile.

Pressing the UP or DOWN button causes the display to show
average horsepower between the two speeds chosen in setup.

Pressing the UP or DOWN button shows the peak horsepower
reached during the test.

G-FORCE

Pressing the MODE button until the display shows G Force.

The display shows the number of horizontal and forward Gs.
The right indicator is sideways acceleration with the arrow
indicating direction. The left is forward acceleration. The arrow
points up when speed is increasing and down when speed is
decreasing.

Operation

Advertising

Popular Brands

Popular manuals