Red Lion ITMS - Manual (Page 2)

2
SPECIFICATIONS
1. POWER: 18-36 VDC, 3.0 W max. or 24 VAC, ± 10%, 50/60 Hz, 4 VA max.
2. INPUT:
Sample Rate: 67 msec. (15 Hz)
Failed Sensor Response: Open or shorted (RTD only) sensor coils indication,
error code returned in Process Value
Common Mode Rejection: 50/60 Hz, 110 dB min.
Overvoltage: 30 VDC
Response Time: 150 msec. max.
3. THERMOCOUPLE INPUTS:
Types: T, E, J, K, R, S, B, N, C, linear mV
Input Impedance: 20 M
Ω
Lead Resistance Effect: 0.22 µV/ Ω
Resolution: 1° or 0.1° for all types
4. RTD INPUTS:
Type: 2 or 3 wire
Excitation: 150 µA
Lead Resistance: 10
Ω max.
Resolution: 1° or 0.1° for all types
5. INDICATION ACCURACY: ±(0.3% of span, +1°C), includes NIST
conformity, cold junction effect, A/D conversion errors, tempco and
linearization conformity at 23°C after 20 minute warm-up.
Span Drift (max) : 0.01% /°C
6. USER INPUT: Internally pulled up to +5 VDC. V
IL
= 0.78 V max.,
V
IH
= 1.8 V min. I
OFF
= 9 µ A max. 30 V max. over voltage continuously.
7. ISOLATION LEVEL: 1.5 KV @ 50/60 Hz, 1 minute (150 V working)
between input, RS485 and power supply. 2300 Vrms, 1 minute (300 V
working) to relay contacts.
8. SERIAL COMMUNICATIONS:
Type: RS485; RTU and ASCII MODBUS modes
Baud: 300, 600, 1200, 2400, 4800, 9600, 19200, and 38400
Format: 7/8 bit, odd, even and no parity
Transmit Delay: Programmable. (See Transmit Delay explanation in Step 6)
Transmit Enable (TXEN): (primarily for 20 mA loop converter) open
collector V
OH
= 10 VDC max. V
OL
= 0.5 VDC @ 5 mA max. current limit
9. A/D CONVERTER: 16 bit resolution
10. RELAY OUTPUTS:
Type: 1 Form A N.O. contacts, 1 Form C DPDT
Rating: 5A @ 30 VDC or 250 VAC max. (resistive)
1/10 HP @ 120 VAC (inductive)
Response Time: 155 msec. max. to close including step response, 153 msec.
max. to open.
Output On Delay Time: Programmable from 0 to 32000 sec ±0.01% - 1 sec. max.
11. MEMORY: Nonvolatile E 2 PROM retains all programmable parameters.
12. ENVIRONMENTAL CONDITIONS:
Operating Temperature Range: -20 to +65 °C
Storage Temperature Range: -40 to +85 °C
Operating and Storage Humidity: 85% max. relative humidity (non-
condensing) from -20 to +65
°C
Altitude: Up to 2000 meters
13. CERTIFICATIONS AND COMPLIANCE:
SAFETY
UL Recognized Component, File # E179259, UL3101-1, CSA 22.2 No. 1010-1
Recognized to U.S. and Canadian requirements under the Component
Recognition Program of Underwriters Laboratories, Inc.
IECEE CB Scheme Test Certificate # US/5141A/UL,
CB Scheme Test Report # 01ME11540-0702001
Issued by Underwriters Laboratories, Inc.
IEC 1010-1, EN 61010-1: Safety requirements for electrical equipment
for measurement, control, and laboratory use, Part 1.
ELECTROMAGNETIC COMPATIBILITY
Notes:
1. This device was designed for installation in an enclosure. To avoid
electrostatic discharge to the unit in environments with static levels above
6 KV, precautions should be taken when the device is mounted outside an
enclosure. When working in an enclosure (ex. making connections, etc.),
typical anti-static precautions should be observed before touching the module.
Refer to the EMC Installation Guidelines section of this bulletin for
additional information.
14. CONSTRUCTION: Case body is black high impact plastic. Installation
Category II, Pollution Degree 2.
15. CONNECTIONS: Wire clamping screw terminals.
16. MOUNTING: Universal mounting foot for attachment to standard DIN
style mounting rails, including top hat (T) profile rail according to EN50022
- 35 x 7.5 and -35 x 15, and G profile rail according to EN50035 - G32.
17. WEIGHT: 4.5 oz. (127.57 g)
Power mains class A
Enclosure class A EN 55011 RF interference
Emissions to EN 55011
Level 3; 10 V/m ENV 50204 Simulation of cordless telephone
150 KHz - 80 MHz
Level 3; 10 V/rms EN 61000-4-6 RF conducted interference
Level 3; 2 KV power
Level 4; 2 KV I/O EN 61000-4-4 Fast transients (burst)
80 MHz - 1 GHz
Level3; 10 V/M EN 61000-4-3 Electromagnetic RF fields
Level 3; 8 KV air 1
Level 2; 4 KV contact EN 61000-4-2 Electrostatic discharge
200 Hz, 50% duty cycle
Immunity to EN 50082-2
900 MHz ± 5 MHz
BLOCK DIAGRAM
RTD TYPE INPUT TYPE RANGE
385
100 Ω platinum,
Alpha=.00385
-200 to +800°C
-328 to +1472°F
392
100 Ω platinum,
Alpha=.003919
-200 to +800°C
-328 to +1472°F
672
120 Ω nickel,
Alpha=.00672
-80 to +260°C
-112 to +500°F
Ohms Linear Resistance 0 to 440 Ω
TC TYPE DISPLAY RANGE
WIRE COLOR
ANSI BS 1843
T
-200 to +400°C
-328 to +752°F
(+) blue
(-) red
(+) white
(-) blue
E
-200 to +750°C
-328 to +1382°F
(+) violet
(-) red
(+) brown
(-) blue
J
-200 to +760°C
-328 to +1400°F
(+) white
(-) red
(+) yellow
(-) blue
K
-200 to +1372°C
-328 to +2502°F
(+) yellow
(-) red
(+) brown
(-) blue
R
0 to +1768°C
+32 to +3214°F
No Standard
(+) white
(-) blue
S
0 to +1768°C
+32 to +3214°F
No Standard
(+) white
(-) blue
B
+200 to +1820°C
+392 to +3308°F
No Standard No Standard
N
-200 to +1300°C
-328 to +2372°F
(+) orange
(-) red
(+) orange
(-) blue
C
W5/W26
0 to +2315°C
+32 to +4199°F
No Standard No Standard
mV -10 mV to 65 mV NA NA