Kenwood KDV-MP5343U - Manual (Page 31)

English | 31
Appendix
For operating KCA-BT200 (Optional)
For operation refer to Model-A-1 in the Instruction
Manual of KCA-BT200, and the table below. The
[AUTO]/[TI] button should be replaced with [SRC]
button for <Answering the Waiting Call after
Terminating>.
Set the remote controller mode switch to “AUD” mode
before starting operation.
Notation used in the KCA-BT200
Instruction Manual Operation
[ 38] button [AUD] knob* 1
Control knob [AUD] knob
[AUTO]/[TI] button [DISP] button
Control knob towards up or down [FM+] or [AM–] button
Control knob towards left or right [ 4] or [¢] button
* 1 Use the [ 38] button for the operation of <Switching to the
Private Mode>.
For operating KCA-BT100 (Optional)
To control KCA-BT100, operate as follows;
To make setting for <Selecting the Dialing Mode>,
select <Function Control> (page 10). Pressing the
[AUD] knob for at least 1 second after selecting
the "D.MODE" item allows you to enter the dialing
method selection mode. To exit from dialing method
selection mode, press Search button.
To make <Disconnecting a Call>, <Clearing the
Disconnection Message>, and <Rejecting an
Incoming call>, press [DISP] button for at least 1
second.
Set the remote controller mode switch to “AUD” mode
before starting operation.
Moreover, some displays are different from the
description of KCA-BT100 Instruction Manual.
Displays of KCA-BT100 Instruction
Manual Actual displays on this unit
“DISCONCT” “HF D-CON”
“CONNECT” “HF CON”
“PHN-DEL” “DVC-DEL”
“P-STATUS” “D-STATUS”
“BT-CON Y”
“HF-CON Y”
“BT-CON N” “HF-CON N”
Function Glossary
• “AUTO1”, “AUTO2”, “MANUAL” (Tuning mode
select)
Select a tuning mode of the radio.
Tuning mode Display Operation
Auto seek “AUTO1” Automatic search for a station.
Preset station seek “AUTO2” Search in order of the stations in the
Preset memory.
Manual “MANUAL” Normal manual tuning control.
• “AVIN” (Audio/ visual input)
When this is set to ON, AV input source can be
selected.
ON1: Allows AV input source to be selected. Use
this setting when the built-in AV IN terminal is
connected to the external equipment all the
time.
ON2: Activates the attenuator function when
turning on the power with AV input source
selected. Cancel the attenuator function
by turning the volume knob clockwise
when listening to the audio of the external
equipment.
OFF: Disable AV input source selection. Use this
setting when the built-in AV IN terminal is not
used.
• DTA (Digital Time Alignment)
Make fine adjustment of the delay time of the
speaker output specified at <Cabin selection>
(page 27) to have a more suitable environment for
your vehicle.
The settings of the delay time are automatically
identified and compensated by specifying the
distances of each speaker from the center of the
vehicle interior.
1 Set the front and rear positions and the height
of the reference point to the position of the ears
of the person sitting in the front seat, and set
the right and left positions to the center of the
vehicle interior.
2 Measure the distances from the reference point
to the speakers.
3 Calculate the distance difference in accordance
with the farthest speaker.
Next page 3
B64-4430-00_00_M_English.indd 31 B64-4430-00_00_M_English.indd 31 09.2.13 10:19:21 AM 09.2.13 10:19:21 AM