Audio settings – Kenwood KDC-BT44U User Manual
Page 16
14
Data Size:
B6L (182 mm x 128 mm)
Book Size:
B6L (182 mm x 128 mm)
AUDIO SETTINGS
While listening to any source...
1 Press the volume knob to enter [FUNCTION].
2 Turn the volume knob to select [AUDIO CONTROL], then press the
knob.
3 Turn the volume knob to make a selection (see the following table),
then press the knob.
Repeat
step
3 until the desired item is selected or activated.
4 Press and hold
to exit.
To return to the previous setting item or hierarchy, press
.
Default: XX
SUB-W LEVEL –15 to +15 (0)
Adjusts the subwoofer output level.
BASS LEVEL
–8 to +8 (+6)
Adjusts the level to memorize for each source. (Before
making an adjustment, select the source you want to
adjust.)
MID LEVEL
–8 to +8 (+5)
TRE LEVEL
–8 to +8 (0)
EQ PRO
BASS ADJUST BASS CTR FRQ
60/ 80/ 100/ 200HZ: Selects the center frequency.
BASS LEVEL
–8 to +8 (+6): Adjusts the level.
BASS Q FACTOR
1.00/ 1.25/ 1.50/ 2.00: Adjusts the quality factor.
BASS EXTEND
ON: Turns on the extended bass. ; OFF: Cancels.
MID ADJUST MID CTR FRQ
0.5/ 1.0/ 1.5/ 2.5KHZ: Selects the center frequency.
MID LEVEL
–8 to +8 (+5): Adjusts the level.
MID Q FACTOR
0.75/ 1.00/ 1.25: Adjusts the quality factor.
TRE ADJUST
TRE CTR FRQ
10.0/ 12.5/ 15.0/ 17.5KHZ: Selects the center
frequency.
TRE LEVEL
–8 to +8 (0): Adjusts the level.
PRESET EQ
DRIVE EQ/ TOP40/ POWERFUL/ ROCK/ POPS/ EASY/ JAZZ/
NATURAL/ USER: Selects a preset equalizer suitable to the music genre.
(Select [USER] to use the customized bass, middle, and treble settings.)
[DRIVE EQ] is a preset equalizer that reduces noise from the road.
BASS BOOST
LEVEL1
/ LEVEL2/ LEVEL3: Selects your preferred bass boost level. ;
OFF:
Cancels.
LOUDNESS
LEVEL1/ LEVEL2: Selects your preferred low and high frequencies boost
to produce a well-balanced sound at a low volume level. ; OFF: Cancels.
SUBWOOFER SET
ON: Turns on the subwoofer output. ; OFF: Cancels.
LPF SUBWOOFER
THROUGH: All signals are sent to the subwoofer. ; 85HZ/ 120HZ/
160HZ: Audio signals with frequencies lower than 85 Hz/ 120 Hz/
160 Hz are sent to the subwoofer.
SUB-W PHASE
REVERSE (180°)/ NORMAL (0°): Selects the phase of the subwoofer
output to be in line with the speaker output for optimum performance.
(Selectable only if a setting other than [THROUGH] is selected for
[LPF SUBWOOFER].)
FADER
R15 to F15 (0): Adjusts the rear and front speaker output balance.
BALANCE
L15 to R15 (0): Adjusts the left and right speaker output balance.
VOLUME OFFSET
(Default: 0)
–8 to +8 (for AUX) ; –8 to 0 (for other sources): Presets the volume
adjustment level of each source. (Before adjustment, select the source
you want to adjust.)
SOUND RECNSTR
(Sound
reconstruction)
ON: Creates realistic sound by compensating the high-frequency
components and restoring the rise-time of the waveform that are lost in
audio data compression. ; OFF: Cancels.
• [SUB-W LEVEL]/ [SUBWOOFER SET]/ [LPF SUBWOOFER]/ [SUB-W PHASE] is
selectable only if [SWITCH PREOUT] is set to [SUBWOOFER]. ( 4)
• [SUB-W LEVEL]/ [LPF SUBWOOFER]/ [SUB-W PHASE] is selectable only if
[SUBWOOFER SET] is set to [ON].
JS_KWD_KDC_BT44U_EWE0_01_EN.indd 14
JS_KWD_KDC_BT44U_EWE0_01_EN.indd 14
20/11/2013 4:15:18 PM
20/11/2013 4:15:18 PM