Asus A8N32-SLI - Manual (Page 83)

A S U S A 8 N 3 2 - S L I D e l u x e A S U S A 8 N 3 2 - S L I D e l u x e A S U S A 8 N 3 2 - S L I D e l u x e A S U S A 8 N 3 2 - S L I D e l u x e A S U S A 8 N 3 2 - S L I D e l u x e 4 - 1 5 4 - 1 5 4 - 1 5 4 - 1 5 4 - 1 5
4.3.5 4.3.5 4.3.5 4.3.5 4.3.5 Primary, Secondary, Third, Fourth, Fifth, Primary, Secondary, Third, Fourth, Fifth, Primary, Secondary, Third, Fourth, Fifth, Primary, Secondary, Third, Fourth, Fifth, Primary, Secondary, Third, Fourth, Fifth,
and Sixth IDE Master/Slave
and Sixth IDE Master/Slave and Sixth IDE Master/Slave and Sixth IDE Master/Slave and Sixth IDE Master/Slave
The BIOS automatically detects the connected IDE devices. There is a
separate sub-menu for each IDE device. Select a device item, then press
<Enter> to display the IDE device information.
The BIOS automatically detects the values opposite the dimmed items
(Device, Vendor, Size, LBA Mode, Block Mode, PIO Mode, Async DMA, Ultra
DMA, and S.M.A.R.T. monitoring). These values are not user-configurable.
These items show N/A if no IDE device is installed in the system.
Type [Auto] Type [Auto] Type [Auto] Type [Auto] Type [Auto]
Selects the type of IDE drive. Setting to [Auto] allows automatic selection
of the appropriate IDE device type. Select [CDROM] if you are specifically
configuring a CD-ROM drive. Select [ARMD] (ATAPI Removable Media
Device) if your device is either a ZIP, LS-120, or MO drive.
Configuration options: [Not Installed] [Auto] [CDROM] [ARMD]
LBA/Large Mode [Auto] LBA/Large Mode [Auto] LBA/Large Mode [Auto] LBA/Large Mode [Auto] LBA/Large Mode [Auto]
Enables or disables the LBA mode. Setting to [Auto] enables the LBA mode
if the device supports this mode, and if the device was not previously
formatted with LBA mode disabled. Configuration options: [Disabled]
[Auto]
Block (Multi-sector Transfer) [Auto] Block (Multi-sector Transfer) [Auto] Block (Multi-sector Transfer) [Auto] Block (Multi-sector Transfer) [Auto] Block (Multi-sector Transfer) [Auto]
Enables or disables data multi-sectors transfers. When set to [Auto], the
data transfer from and to the device occurs multiple sectors at a time if
the device supports multi-sector transfer feature. When set to [Disabled],
the data transfer from and to the device occurs one sector at a time.
Configuration options: [Disabled] [Auto]
V00.00 (C)Copyright 1985-2004, American Megatrends, Inc.
BIOS SETUP UTILITY
Main
Primary IDE Master
Device : Hard Disk
Vendor : xxxxxxxxx
Size : xx.xGB
LBA Mode : Supported
Block Mode : 16 Sectors
PIO Mode : 4
Async DMA : MultiWord DMA-2
Ultra DMA : Ultra DMA-5
S.M.A.R.T. : Supported
Type [Auto]
LBA/Large Mode [Auto]
Block(Multi-sector Transfer) [Auto]
PIO Mode [Auto]
DMA Mode [Auto]
S.M.A.R.T. [Auto]
32Bit Data Transfer [Disabled]
→← →← →← →← →← Select Screen
↑↓ ↑↓ ↑↓ ↑↓ ↑↓ Select Item
+- Change Field
Tab Select Field
F1 General Help
F10 Save and Exit
ESC Exit