Samsung LE46D679M3S - Manual (Page 39)

39
English
04
Advanced Featur
es
¦ Listening through a Receiver
You can listen to sound through a receiver (i.e Home Theatre) instead of the TV speaker.
1. Select Receiver and set to On.
2. Press the
EXIT button to exit.
✎
If your receiver supports audio only, it may not appear in the device list.
✎
The receiver will work when you have properly connected the optical in jack of the receiver to the DIGITAL AUDIO
OUT (OPTICAL) jack of the TV.
✎
When the receiver (i.e Home Theatre) is set to On, you can hear sound output from the TV’s Optical jack. When the
TV is displaying a DTV (aerial) signal, the TV will send out 5.1 channel sound to the receiver. When the source is a
digital component such as a DVD and is connected to the TV via HDMI, only 2 channel sound will be heard from
the receiver.
✎
NOTE
x You can only control Anynet + devices using the TV remote control, not the buttons on the TV.
x The TV remote control may not work under certain conditions. If this occurs, reselect the Anynet + device.
x The Anynet + functions do not operate with other manufacturers’ products.
¦ Troubleshooting for Anynet +
Problem Possible Solution
Anynet + does not work. • Check if the device is an Anynet + device. The Anynet + system supports Anynet + devices only.
• Connect only one receiver (home theatre).
• Check if the Anynet
+ device power cord is properly connected.
• Check the Anynet + device’s Video/Audio/HDMI Cable connections.
• Check whether Anynet + (HDMI-CEC) is set to On in the Anynet + setup menu.
• Check whether the TV remote control is in TV mode.
• Check whether it is Anynet
+ exclusive remote control.
• Anynet + does not work in certain situations. (Searching channels, operating Media Play or Plug & Play (Initial
setup), etc.)
• When connecting or removing the HDMI cable, please make sure to search devices again or turn your TV off
and on again.
• Check if the Anynet + Function of Anynet + device is set on.
I want to start Anynet + . • Check if the Anynet + device is properly connected to the TV and check if the Anynet + (HDMI-CEC) is set to On
in the Anynet + Setup menu.
• Press the TOOLS button to display the Anynet + menu and select a menu you want.
I want to exit Anynet + . • Select View TV in the Anynet + menu.
• Press the SOURCE button on the TV remote control and select a device other than Anynet + devices.
• Press P >/<, PRE-CH , and FAV.CH to change the TV mode. (Note that the channel button operates only
when a tuner-embedded Anynet + device is not connected.)
The message “Connecting to
Anynet
+ device...” appears on the
screen.
• You cannot use the remote control when you are configuring Anynet + or switching to a view mode.
• Use the remote control when the Anynet + setting or switching to view mode is complete.
The Anynet + device does not play. • You cannot use the play function when Plug & Play (Initial setup) is in progress.
The connected device is not
displayed. • Check whether or not the device supports Anynet + functions.
• Check whether or not the HDMI Cable is properly connected.
• Check whether Anynet
+ (HDMI-CEC) is set to On in the Anynet + setup menu.
• Search Anynet + devices again.
• You can connect an Anynet + device using the HDMI Cable only. Some HDMI cables may not support Anynet +
functions.
• If it is terminated by an abnormal situation such as disconnecting the HDMI cable or power cord or a power
failure, please repeat the device scan.
The TV programme cannot be
recorded. • Check whether the antenna jack on the recording device is properly connected.
The TV sound is not output
through the receiver. • Connect the optical cable between TV and the receiver.
[LD679-ZG]BN68-03378A-L04.indb 39 2011-04-12 �� 10:23:26