Document Outline

• user’s GUIDE
  • AT-8116
  • Fast Ethernet Intelligent Switch
• Table of Contents
• Chapter1
  • Administrative Interface
    • Features
    • Network Management Systems
    • Accessing the SNMP Agent
    • System Requirements
      • Hardware Requirements
      • Software Requirements
      • Because of their compatibility and reliability, th...
    • VT100 Terminal Settings
    • Testing the Installation
    • Accessing the Command Line Interface Remotely
• Chapter2
  • Command Line Interface
    • Features of the Command Line Interface
    • Entering Commands
      • The command is reprinted after the prompt, and the...
    • System Commands
      • Table21 System Commands
      • Table22 Commands Matching <get-c>
    • Command Line Interface Structure
      • Table23 Commands Groups
• Chapter3
  • Console Commands
    • Table31 Console Function Keys
      • banner
      • clear
      • login
      • logout
      • set-page
      • set-prompt
      • set-attr-prompt
      • set-attr-msg
      • set-attr-text
      • set-passwd
• Chapter4
  • System Commands
    • sys-stat
    • i/f 1 -- description [Port 1 - 10/100BaseTx ETHERN...
    • i/f 2 -- description [Port 2 - 10/100BaseTx ETHERN...
    • i/f 3 -- description [Port 3 - 10/100BaseTx ETHERN...
    • i/f 4 -- description [Port 4 - 10/100BaseTx ETHERN...
    • i/f 5 -- description [Port 5 - 10/100BaseTx ETHERN...
    • i/f 6 -- description [Port 6 - 10/100BaseTx ETHERN...
    • i/f 7 -- description [Port 7 - 10/100BaseTx ETHERN...
    • i/f 8 -- description [Port 8 - 10/100BaseTx ETHERN...
    • i/f 9 -- description [Port 9 - 10/100BaseTx ETHERN...
    • i/f 10 -- description [Port 10 - 10/100BaseTx ETHE...
    • i/f 11 -- description [Port 11 - 10/100BaseTx ETHE...
    • i/f 12 -- description [Port 12 - 10/100BaseTx ETHE...
    • i/f 14 -- description [Port 14 - 10/100BaseTx ETHE...
    • i/f 15 -- description [Port 15 - 10/100BaseTx ETHE...
    • i/f 16 -- description [Port 16 - 10/100BaseTx ETHE...
      • SYS_console>
      • get-stst-level
      • set-stst-level <level>
      • warm-reset
      • cold-reset
      • get-last-err
    • Software resets number implies executed “warm rese...
      • init-nvram
      • get-sw-file
      • set-sw-file
      • get-tftp-srvr
      • set-tftp-srvr
      • set-tftp-mode
      • get-tftp-mode
      • sw-dnld
      • set-fg-param
      • start-fg
      • stop-fg
• Chapter5
  • IP Commands
    • get-ip
    • set-ip
    • get-ip-cfg
    • set-ip-cfg
    • If the IP configuration is not specified, the agen...
      • clear-ip-cfg
      • get-gatew
      • set-gatew
• Chapter6
  • Address Resolution Commands
    • get-arp-tbl
    • del-arp-entry
    • add-arp-entry
• Chapter7
  • Ping Commands
• Chapter8
  • SNMP Commands
    • SNMP Community String Commands
      • get-comm
      • set-comm
    • SNMP Trap Message Commands
      • get-auth
      • set-auth
      • get-traps
      • add-trap
      • del-trap
      • get-rmon-state
• Chapter9
  • Switching Database Commands
    • Learning Table
      • get-lt-entry
      • get-lt-16
      • find-lt-addr
      • del-lt-entry
      • del-lt-addr
      • add-lt-entry
      • DPORT is a decimal number representing the ID of t...
        • get-lt-age
        • set-lt-age
• Chapter10
  • Virtual LAN Commands
    • Virtual Broadcast Domains (VBC)
      • get-con-matrix
      • del-vbc-domain
      • When you use the set-vbc-domain command with the a...
      • All ports not defined as a member of a VBC are mem...
        • get-vbc-matrix
        • Security VLANs
        • set-sec-vlan
      • Table101 SVLAN Groups
        • del-sec-vlan
        • Setting a security VLAN group with the “all” param...
          • get-svlan-tbl
        • If you assign ports to multiple SVLANs, they becom...
          • get-svlan-matrix
• Chapter11
  • Port Monitoring Commands
    • set-mon-port
    • stop-mon
    • get-nv-mon
    • save-mon
    • clear-nv-mon
• Chapter12
  • Port Configuration Commands
    • get-port-cfg
    • PORT_ID LAN_TYPE LINK IF_TYPE SPEED_SEL LAN_SPEED ...
    • ==================================================...
    • 1 ETH10/100OFF TP FORC100 100Mbps OFF ON 2 ETH...
    • SYS_console>
      • set-port-dplex
      • set-speed-sel
    • If the port’s link partner is in Full Duplex mode ...
      • set-port-state
      • set-aggr-mode
• Chapter13
  • Switching Statistics Commands
    • clr-cnt
    • get-colls-cnt
    • get-rmon-cnt
    • get-sdist-cnt
    • get-mgm-brcnt
• Chapter14
  • Spanning Tree Commands
    • get-stp
    • The default state is disabled for spanning tree.
      • set-stp
      • get-st-bcfg
      • get-st-pcfg
      • get-st-syscfg
      • set-br-prio
      • set-br-maxage
      • set-br-hellot
      • set-br-fwdel
      • set-prt-prio
      • set-prt-enb
      • set-prt-pcost
• Chapter15
  • Using an SNMP Manager
    • Configuring the AT-8116 SNMP Agent
      • Global Setup
        • 1. Connect a terminal to the RS-232 connector.
        • 2. Log in to the Command Line Interface.
        • 3. Initialize all the AT-8116 parameters to their ...
        • 4. Wait until you see the LOGIN prompt again. Logi...
      • IP Setup
        • 1. Modify the system IP configuration to match you...
        • 2. Set the default gateway address using the set-g...
        • 3. Confirm that the default gateway IP address was...
      • SNMP Setup
        • 1. Set up the SNMP communities strings for the two...
• Chapter16
  • Software Troubleshooting
• AppendixA
  • Software Downloading
    • Requirements
      • When the file transfer is completed, the AT-8116 a...
    • 8116 TFTP Client Download Procedure
      • 1. Insure that an IP Address is assigned.
      • 2. Set the TFTP mode to client using the set-tftp-...
      • 3. Insure that the host system for the TFTP server...
      • 4. Insert the diskette with the software file into...
      • 5. Select/Create a directory into which to copy th...
      • 6. Copy the software file into a file with a suita...
      • 7. Set the remote software file using the set-sw-f...
      • 8. Operate TFTP server on the remote system host a...
    • 8118 TFTP Server Download Procedure
      • 1. Insure that an IP Address is assigned.
      • 2. Set the TFTP mode to the server using the set-t...
      • 3. Set the remote software file using the set-sw-f...
      • 4. Insure that the host system for the TFTP client...
      • 5. Insert the diskette with the software file into...
      • 6. Select/Create a directory into which to copy th...
      • 7. Copy the software file into a file with a suita...
      • 8. Set the remote software file using the set-sw-f...
      • 9. Use the sw-dnld command to start download.
      • 10. Operate the remote TFTP client.
      • 11. Select binary transfer mode if the code is in ...
      • 12. Using the TFTP protocol, send the file (to be ...
• AppendixB
  • System Defaults
    • TableB1 System Default Values
• AppendixC
  • Command Line Reference
    • TableC1 Console Commands
    • TableC2 System Commands
    • TableC3 IP Commands
    • TableC4 SNMP Commands
    • TableC5 Switching Database Commands
    • TableC6 Virtual LAN Commands
    • TableC7 Port Configuration Commands
    • TableC8 Switching Statistics Commands
    • TableC9 Spanning Tree Commands