Audiovox Rampage AV-455 User Manual

Page 8

Advertising

from the display panel). To return to stereo reception

mode, press the button again so that the “ST” indication

appears on the display panel.

PRE-SET SCAN (PS)

AUTO-STORE TUNING (AS)

Press this button momentarily to scan the stations

pre-set into the memories of the band in use. The unit

will stop at each pre-set station for 5 seconds before

continuing to the next pre-set station (the pre-set

number

the

display

panel

will

flash

during

Pre-Set

Scan

operation).

Press

the

button

again

momentarily

to stop Pre-Set Scan operation and remain on the

selected frequency.

Pressing and holding the button for longer than 2

seconds will activate the Auto-Store Tuning feature

(“ATP will appear on the display panel) which will

automatically scan and enter up to 6 stations into the

pre-set memories on the band in use. After entering

the stations into the memories, the unit will

automatically stop at each station for 5 seconds so

each can be heard. If you have already set the pre-set

memories to your favorite stations, activating the

Auto-Store Tuning feature will erase those stations

and enter the new ones. This feature is most useful

when travelling in a new area where you are not familiar

with the local stations.

STATION PRE-SET MEMORIES

To set any of the 6 pre-set memories in each band, use

the following procedure:

1. Turn the radio on and select the desired band.

2. Select the first station to be pre-set using the Manual

Up/Down or Automatic Seek Tuning Controls

3. Press the pre-set button to be set and continue to

hold it in for approximately 2 seconds. The pre-set

number will appear on the display panel indicating

that the station is now set into that pre-set memory

position. The station can now be recalled at any

time by pressing that button.

4. Repeat the above procedure for the remaining 5 pre-

sets on that band and for the other 4 bands on the unit.

LIQUID CRYSTAL DISPLAY PANEL

The Liquid Crystal Display (LCD) panel displays the

frequency, time, and activated functions.

N O T E

N O T E:

:It is a characteristic of LCD panels that, if

subjected to cold temperatures for an extended

period of time, they may take longer to illuminate

than under normal conditions. In addition, the

visibility of the numbers on the LCD may slightly

decrease. The LCD read-out will return to normal

when the temperature increases to a normal range.

SPECTRUM ANALYZER DISPLAY

The Spectrum Analyzer Display feature incorporated

in this unit breaks down the audio frequency spectrum

into 5 bands and provides a visual indication of the

amount of audio signal within each of these bands.

The number of illuminated bars (1 to 10) shows the

instantaneous signal level in the band around the

indicated frequencies (105Hz., 340Hz., 1KHz.,

3.4KHz., and 10.5KHz.).

CASSETTE DOOR

To access the cassette door, press the Front Panel

Release button

so that the panel drops to its

lowered

position.

Hold

the

cassette

with

the

exposed

tape edge to the right and insert it fully into the

cassette door until the cassette is engaged and

begins playing (“TAPE” will appear on the display

panel). When the cassette reaches the end on the

side of the tape being played, the unit will automatically

change direction of play as shown by the arrow

indications on the display panel.

N O T E

N O T E:

:Observe cassette operation cautions in Care

and Maintenance section of this manual.

FAST-FORWARD/REWIND BUTTONS

(

)

These buttons cause the tape to move rapidly in the

direction indicated by the arrows. For example, if the

button is pushed when the tape is moving from left

to right (

on the display panel), the tape will fast-

forward. If the button is pressed while the tape is

moving from right to left (

on the display panel), the

tape will rewind. To stop fast tape movement, lightly

push the opposite button. If the tape is allowed to fast-

forward or rewind all the way to the end, play will

automatically begin again from that point.

PROGRAM SELECTOR

To manually reverse tape direction and play the other

side (program) of the cassette, lightly push both the

Fast-Forward and Rewind buttons

and

at the

same time. The change of direction will be shown by

the arrows on the display panel.

EJECT BUTTON (

)

Tape playback is stopped and the cassette is ejected

by pressing this button located behind the front panel,

next to the tape door. Radio operation will automatically

128-5504

8 of 12

OPERATING

INSTRUCTIONS

OPERATING

INSTRUCTIONS

OPERATING

INSTRUCTIONS

OPERATING

INSTRUCTIONS

OPERATING

INSTRUCTIONS

Advertising

Popular Brands

Popular manuals