Document Outline

• CONTENTS
• BEFORE YOU BEGIN
  • Parts List
  • About Caller Identification (Caller ID)
  • About the Calls Log
  • About Adding Handsets
• INSTALLATION
  • Table/Desk Installation
    • 1 Connect the telephone line cord.
    • 2 Connect the power cord.
    • 3 Install the handset battery.
    • 4 Charge the handset battery.
    • 5 Check for dial tone.
  • About Handset Registration
  • Register an Additional Handset (Model 5800 Handset)
  • Wall Installation
    • 1 Connect the power cord and telephone line cord to the underside of the base, as shown (figure a).
    • 2 Position the mounting bracket as shown (figure b).
    • 3 Feed the telephone line cord through the hole in the center of the mounting bracket (figure b), align the bracket with the base, and slide it into the hole on the base as shown (figure c).
    • 4 Lock the mounting bracket in place (figure d).
    • 5 Plug the telephone line cord into a modular wall jack, and mount the base on the wall (figure e).
    • 6 Plug the power cord into an electrical outlet not controlled by a wall switch (figure e).
    • 7 Follow Steps 3–5 in “Table/Desktop Installation.”
  • Spare Battery/Power Failure Backup
  • Belt Clip
  • Headset
• FEATURE SETUP
  • HANDSET
    • Feature Setup Menu
    • Set Time
    • Clock Mode
    • REGISTER
    • Sound Select
    • Ringer Volume
    • Ringer Melody
    • Low Batt Tone
    • Range Tone
    • Keypad Tone
    • Set Contrast
    • Language Setting
  • BASE
    • Ringer Volume
    • Ringer Melody
• TELEPHONE OPERATION
  • Make a Call
  • Answer a Call
  • Volume
  • Handset Speakerphone
  • Redial
  • Flash/Call Waiting
  • Mute
  • Hold
  • DISPLAY SCREEN MESSAGES
  • HANDSET ICONS
  • BASE LIGHTS
  • TONES AND WHAT THEY MEAN
• INTERCOM OPERATION
  • Intercom Calls
    • From Base to All Handsets
    • From Handset to Base
    • From Handset to Handset
    • From Handset to Base/Handset(s)
  • Answering Intercom
  • End Intercom
  • To Answer an Incoming Call While Intercomming
    • To end the intercom call and answer the incoming call:
    • To conference the incoming call with the intercom call:
  • Blind Call Transfer
  • Announced Call Transfer
  • Conference Calling
• PHONE BOOK
  • Store a Number and Name in Phone Book
  • Keypad Characters
  • Dial a Number in Phone Book
  • Edit a Number/Name in Phone Book
  • Delete a Number/Name in Phone Book
• CALLER ID OPERATION
  • CALLER ID OPERATION
  • Review Calls Log
  • Store Record in Phone Book
  • Display Dial
  • Remove Call Records
    • Removing a Specific Call Record
    • Removing All Records
• Answering system operation
  • at the base
    • Audible Indicators
    • Turn Answering System On/Off
    • Set the Clock
    • About Mailboxes
    • About Announcements
    • Record Your Announcement
    • Answering System Feature Setup
    • FETURE SUMMARY
    • Listen to, Save & Delete Messages
    • Adjust Playback Volume
    • Call Screening/Intercept
    • Record a Memo
    • MESSAGE WINDOW DISPLAY
  • at touch tone phone
    • Connect with the Answering System
    • Voice Menu
    • REMOTE ACCESS COMMANDS
• BATTERIES
  • Battery Life
  • Battery Indicator
  • Charge the Handset Battery Pack
  • Spare Battery
  • Replace the Handset Battery Pack
• IN CASE OF DIFFICULTY
  • PHONE
    • If the phone does not work at all, check these items first
    • If you have no dial tone:
    • If you hear two beeps when you try to use the handset
    • To re-initialize the handset and base
    • If you hear noise or interference when using the phone
    • If your handset displays ENTER BASE ID or NO BASE SUBSCRIPTION
    • If the phone does not ring when you receive a call
  • CALLER ID
    • If the caller’s name or phone number is not displayed
    • If the caller’s name or phone number is not displayed during Call Waiting
  • ANSWERING SYSTEM
    • If messages are incomplete
    • If you have difficultyhearing messages
    • If callers are unable to leave messages in Mailbox 2 or 3
    • If the system does not answer after the correct number of rings
    • If CL appears in the message window
    • If the system does not respond to commands form a remote touch tone phone
    • If your outgoing announcement isn't clear
• DEFAULT SETTINGS
• TECHNICAL SPECIFICATIONS
• INDEX