Sony KDL-46VL160 - Manual (Page 2)

KDL-40/46VL160 EN 4-146-180-11(1)
VIDEO OUT COMPONENT VIDEO OUT DIGITAL OUT PCM/DTS/DOLBY DIGITAL 5.1CH OUTPUT VIDEO Y L
R
AUDIO OUT L
R WOOFER
COAXIAL OPTICAL FRONT REAR CENTER
S VIDEO HDMI OUT
AC IN PB/CB
PR/CR
OPT IN SAT OPT IN VIDEO 1 COAX IN AUDIO IN DVD
DVD IN SAT IN VIDEO 2/BD IN OUT
ANTENNA SA-CD/CD AUDIO IN TV AUDIO IN FRONT R VIDEO 1 DMPORT
DIGITAL
SPEAKERS
HDMI AM
R
L
R
L
FRONT L SUR R SUR L CENTER SUBWOOFER
CABLE / ANTENNA
4
1 3 1
3
IN VIDEO IN
VIDEO
L (MONO)
AUDIO
R
S VIDEO
COMPONENT IN
RGB
PC IN
AUDIO OUT
(VAR/FIX) (1080p/1080i/720p/480p/480i)
1
AUDI AUDI AUDIO AUDIO
P B
P R
Y
2
L
R O
L
R O R L
DIGITAL
OUT (OPTICAL)
AUDIO
CABLE / ANTENNA
4
1 3 1
3
IN VIDEO IN
VIDEO
L (MONO)
AUDIO R
S VIDEO
COMPONENT IN
RGB
PC IN
AUDIO OUT
(VAR/FIX) (1080p/1080i/720p/480p/480i)
1
AUDI AUDI AUDIO AUDIO
P B
P R
Y
2
L
R O
L
R O R L
DIGITAL OUT (OPTICAL) AUDIO
Required Cable Types for Connection Notes on Connection
Connect your incoming signal source (HD Cable Box, HD Satellite Receiver,
or DVD) with HDMI or component video for the best possible picture quality.
If your connecting equipment has DVI output instead of the HDMI output,
you must use a DVI-to-HDMI cable for the video and also connect an audio
cable for the sound. If this is the case, connect the cable to HDMI IN 4 (input)
of your TV.
P&P/PIP functions require Cable/Antenna connection.
■
■
■
Connect PC’s audio output when using an HD15 connection.
Press PC’s FUNCTION Key + Select Output to transmit to TV.
When using an HD15 connection, adjust TV’s Pitch and Phase
to correct sharpness.
Refer to your Operating Instructions.
■
■
■
■
HD Basic Connection with Home Theater System
Cable/SAT
(dish)
SD Cable Box or
SD Satellite Receiver
Home Theater System
or
HD BRAVIA® Sync™ Basic Connection
PC Connection with SD VCR/DVD
Coaxial
HDMI
DVI-to-HDMI
Component
Composite
Audio (L/R)
Mini-Pin Audio Digital Optical Audio
Audio (L/R) with Mini-Pin
HD15
Blu-ray Disc/DVD
Rear of TV
HD Basic Connection with A/V Receiver
CABLE / ANTENNA
4
1 3 1
3
IN VIDEO IN
VIDEO
L (MONO)
AUDIO
R
S VIDEO
COMPONENT IN
RGB
PC IN
AUDIO OUT
(VAR/FIX) (1080p/1080i/720p/480p/480i)
1
AUDI AUDI AUDIO AUDIO
P B
P R
Y
2
L
R O
L
R O R L
DIGITAL
OUT (OPTICAL)
AUDIO
A/V Receiver Blu-ray Disc/DVD
HD Cable Box or
HD Satellite Receiver
Rear of TV
*A/V Receiver
*Blu-ray Disc
SAT
(Dish)
HD Cable Box or
HD Satellite Receiver
*Rear of TV
Cable/Antenna
CABLE / ANTENNA
4
1 3 1
3
IN VIDEO IN
VIDEO
L (MONO)
AUDIO R
S VIDEO
COMPONENT IN
RGB
PC IN
AUDIO OUT
(VAR/FIX) (1080p/1080i/720p/480p/480i)
1
AUDI AUDI AUDIO AUDIO
P B
P R
Y
2
L
R O
L
R O R L
DIGITAL OUT (OPTICAL)
AUDIO
Notebook PC
Splitter
Rear of TV
VCR/DVD Combo
VCR DVD
* Signifies a BRAVIA Sync capable device.
Programming the Remote Control
Your remote control can be programmed to use other equipment and is
pre-programmed to operate the following Sony equipment.
Function Button Sony Equipment Code Number
DVD DVD Player 31033
AMP Receiver 52172
STB Digital Satellite 01639
Programming Other Equipment
Follow the steps below to program your TV remote control.
1 Look for the code in the Manufacturer’s Code List (see the Operating Instructions) that
corresponds to the equipment you would like to operate with the Sony remote control. If
more than one code is provided, try programming the first code listed. If your equipment’s
code is not listed, visit http://esupport.sony.com/remotecodes for a more
comprehensive list.
2 Press and hold , or simultaneously with the button and release.
When in the programming mode, the FUNCTION button blinks for approximately
30 seconds until a code is entered.
3 Enter the five digit code using  –  while the FUNCTION button is lit. If the code is not
entered within 30 seconds, you must repeat step 2.
4 Press or to confirm the code. If successfully programmed, the FUNCTION button
will blink twice, if not, it blinks five times.
To Confirm the Programming
If you can turn your equipment on and off using the green POWER button, the programming is
complete. If not, try the next code listed.
Note:
In some cases, you may not be able to program your remote control. If this is the case, use
your equipment’s remote control.
Any of the FUNCTION buttons can be programmed to operate other equipment regardless
of the labeling. For example, if programmed with the correct code, a Blu-ray Disc player
can be operated with the button. This is useful if your equipment does not match any
of the labeled buttons.
■
■
POWER PORT 1 PORT 2 PORT 3 PORT 4
LAN (10/100)
CABLE / ANTENNA
4
1 3 1
3
IN VIDEO IN
VIDEO
L (MONO) AUDIO
R
S VIDEO
COMPONENT IN
RGB
PC IN
AUDIO OUT
(VAR/FIX) (1080p/1080i/720p/480p/480i)
1
AUDI AUDI AUDIO AUDIO
P B
P R
Y
2
L
R
O
L
R
O R L
DIGITAL
OUT (OPTICAL)
AUDIO
DLNA Certified™ Connection
SAT
(Dish)
Cable/Antenna
HD Antenna
Cable/Antenna
PC
Ethernet
Connecting a PC to Your BRAVIA TV
Splitter
Splitter
Router
DLNA Certified ™ Media Server
Rear of TV
DISPLAY
VOL CH
MUTING
REC REC PAUSE REC STOP
F2 F1 MENU TOP MENU BD/DVD
JUMP
DVD AMP STB TV
PREV REPLAY ADVANCE NEXT
THEATER SOUND PICTURE WIDE
CC FREEZE
LIGHT POWER TV POWER
SYNC MENU PAUSE
PLAY
FUNCTION
STOP
2
2
4
3
4
This TV is a DLNA Certified™ Photo Viewer.