Sony RHT-G2000 User Manual

Rht-g2000

Advertising
background image

Sony RHT-G2000 (GB/FR/ES) 2-655-428-11(1)

Sony Corporation © 2005 Printed in Malaysia

Note

Install this system so that the power cord can be unplugged from the wall socket
immediately in the event of trouble.

Note on the power extension cords

Connect only the system components to the power extension cords. Be sure not to
exceed the power rating of either extension cord.

RHT-G2000

2-655-428-

11(1)

English

Unpacking the system

1

Open the carton and remove the packing.

When removing the packing, support the front and back of this system

using 2 people.

Note

Do not hold the grille as it may detach from the stand resulting in serious injury.

2

Carry the system using 4 people, supporting the underside.

Pedestal

Installing the TV

Place the TV with the pedestal aligning the tape marks.

Troubleshooting

No sound is heard from the system.

See page 25 of the supplied Operating Instructions.

When using KDS-R50XBR1/KDS-R60XBR1, set [Speaker] to {Off} in the

Audio Settings menu of the TV. Refer to the TV’s operating instructions for
details.

If there is no sound, see the section on the connection and settings in the TV’s

operating Instructions.

2 types of tape are attached to this system.

Remove the tape marks for KDF-E42A10/KDF-E50A10 when you set up KDS-

R50XBR1/KDS-R60XBR1.

KDS-R50XBR1/KDS-R60XBR1

KDF-E42A10/KDF-E50A10

Remarque

Installez ce système de manière à ce que vous puissiez débranchez immédiatement
le cordon d’alimentation de la prise secteur en cas de problème.

Remarque concernant les rallonges des cordons

d’alimentation

Connectez uniquement les composants du système aux rallonges des cordons d’
alimentation. Assurez-vous de ne pas dépasser la puissance nominale de chaque
cordon.

Français

Déballage du système

1

Ouvrez le carton et retirez l’emballage.

Lorsque vous retirez l’emballage, tenez fermement la partie frontale et la

partie arrière du système à l’aide d’une autre personne.

Remarque

Ne tenez pas le meuble TV par la grille de ventilation car celle-ci pourrait se
détacher du panneau et vous risqueriez de vous blesser.

2

Transportez le système avec trois autres personnes en tenant fermement

la partie inférieure.

Socle

Installation du téléviseur

Installez le téléviseur en alignant le socle sur les marques de bande.

Dépannage

Aucun son n’est reproduit par le système.

Reportez-vous à la page 27 du mode d’emploi fourni.

Si vous utilisez les modèles KDS-R50XBR1/KDS-R60XBR1, réglez

[Haut-parleur] sur {Non} dans le menu Audio Settings du téléviseur. Pour de
plus amples informations, reportez-vous aux instructions de fonctionnement
du téléviseur.

S’il n’y a pas de son, reportez-vous à la section des raccordements et réglages

dans le mode d’emploi du téléviseur.

Ce système comporte deux types de marques de bande.

Retirez les marques de bande des modèles KDF-E42A10/KDF-E50A10 si vous

installez les modèles KDS-R50XBR1/KDS-R60XBR1.

KDS-R50XBR1/KDS-R60XBR1

KDF-E42A10/KDF-E50A10

Note to CATV system installer:

This reminder is provided to call the CATV system installer’s attention to
Article 820-40 of the NEC that provides guidelines for proper grounding
and, in particular, specifies that the cable ground shall be connected to the
grounding system of the building, as close to the point of cable entry as
practical.

Advertising