Sony KDL-42XBR950 - Manual

Quic
k Start Guide
~ AC IN
i.LINK
(TS/DV/MICROMV)
DISPLAY SIGNAL OUT
WHITE BLACK
CABLE
VHF/UHF S400
IN OUT
KDL32XBR950
KDL42XBR950
Thank you for purchasing this
Sony product.
After following this step by step
guide you will be able to:
– Insert batteries into the
remote control.
– Connect the display unit to
the media receiver unit.
– Connect a cable or antenna to
your TV.
– Tune your TV .
– Program your remote control
Now you are ready for viewing
TV programs.
© 2003 Sony Corporation
Printed in Japan 4-102-399-01(1)
US
Checking the Supplied
Accessories
1
Remote Control
(RM-Y1000): Two size AA
batteries (R06 Type): Display Interface
Cable:
Antenna Cable: Two AC power
cords:
Inserting Batteries into
the Remote Control
2
1 Open the battery compartment as illustrated below.
2 Insert two size AA batteries (supplied) by matching the e and E
terminals on the batteries to the diagram inside the battery
compartment.
3 Close the battery compartment.
Remove the batteries to avoid damage from possible battery leakage
whenever you anticipate that the remote control will not be used for
an extended period.
Handle the remote control with care.
Avoid dropping it, getting it wet, placing it in direct sunlight, near a
heater, or where the humidity is high.
• Speaker jack covers
(KDL42XBR950 only)
• Operating Instructions
• Quick Start Guide
• Warranty Card
Connecting the
Display Unit to the
Media Receiver Unit
3
1 Connect the display interface cable (supplied) to the DISPLAY
SIGNAL IN jacks, and the AC power cord (supplied) to the AC IN jack
of the unit.
KDL42XBR950
2 Connect the other end of display interface cable to the media receiver
unit’s DISPLAY SIGNAL OUT jacks, and connect the media receiver
unit’s AC power cord (supplied) to the AC IN jack .
Tighten the screw slowly
until the screw is stabilized.
Display Interface cable
(supplied)
KDL32XBR950
When you install KDL42XBR950, use the optional accessories as
follows:
• SONY TABLE TOP STAND: SU-P42T2
• SONY WALL-MOUNT BRACKET: SU-PW2
• SONY FLOATING STAND: SU-PF1
Display Interface
cable (supplied) Tighten the screw
slowly until the
screw is stabilized. AC power cord
(supplied)
BLACK WHITE
DISPLAY SIGNAL IN
SONY EXCLUSIVE CABLE ONLY
Be sure to use the supplied AC power cords.
When connecting optional components, do not connect the AC
power cords to wall outlets until you have completed making all
connections.
Do not tighten the screws too much. It may damage the screws.
Do not use damaged cables, such as cables whose connectors are
deformed.
Handle the display interface cable with care. This unit may fall and
cause injury if accidently knocked or pulled by the connected cable.
To store the AC power cord and the display interface cable in the
stand;
(KDL32XBR950)
See “Storing the AC power cord and the display interface cable
into the stand (KDL32XBR950 only)” on page 28 of the
operating instructions.
(KDL42XBR950)
See the operating instructions for the optional tabletop stand.
Connecting a Cable or
Antenna
4
~ AC IN
i.LINK
(TS/DV/MICROMV)
DISPLAY SIGNAL OUT
WHITE BLACK
CABLE
VHF/UHF S400
The way in which you will connect your TV varies, depending on how
your home receives a signal (cable, cable box, antenna) and whether or
not you plan to connect a VCR or other optional AV equipment.
See examples A, B or C to connect your TV. For details on other
connection examples, see pages 31 to 54 of the operating instructions.
A Cable or Antenna
For best results, use this connection if you are connecting a
cable or an antenna and you;
• Do not need a cable box to unscramble channels.
• Do not intend to connect a VCR.
For antenna connection, use the supplied antenna cable.
B Cable Box and Cable
For best results, use this connection if;
• Your cable company scrambles some channels, such as premium
channels (which requires you to use a cable box), but does not
scramble all channels.
• You do not have a VCR.
75-ohm coaxial cable
(not supplied)
When using an indoor antenna, such as rabbit-ear or dipole-antenna,
keep the antenna away from the display unit. If not, noise may appear
on the screen.
Antenna cable
(supplied)
Rear of Media Receiver Unit
CATV
cable
Splitter
Antenna cable
(supplied)
Cable Box
Rear of Media Receiver Unit
75-ohm
coaxial cable
(not supplied)
75-ohm
coaxial cable
(not supplied)
or
~ AC IN
i.LINK (TS/DV/MICROMV)
DISPLAY SIGNAL OUT
WHITE BLACK
CABLE
VHF/UHF S400
AC power cord
(supplied)