Sony DMX-NV1 - Manual

NETWORKVIDEO RECEIVER Quick Setup Guide
DMX-NV1
© Sony Corporation 2007. Printed in USA. 3-216-111- 11(2)
Package Contents
z Remote control not supplied. To operate this receiver, use your TV’s remote
control equipped with the DMe X button.
z Ethernet cable required (not supplied).
z Using your PC, view the Operating Instruction Manual on the Internet at
http://internet.sony.tv/manual
AC Adapter with
AC Power Cord
Stand
Warranty Card Attachment Guide Quick Setup Guide
NET WO RKV IDE O R ECE IVE R Qu ick Set up Gui de
DM X-N V1
© S ony Co rpo rati on 200 7. P rint ed in U SA.
3-1 26- 111 -11 (1)
Receiver (DMX-NV1)
& Cable Cover
Mounting Bracket
Mounting Knobs Screws, Type 1 Screws, Type 2
USB Cable
HDMI Cable
Setting up the BRAVIA TM Internet Video Link
z If you need to configure a fixed IP address or proxy server, check the Operating Instruction Manual for more information.
POWER PORT 1 PORT 2 PORT 3 PORT 4
Gaming Adapter as Wireless Bridge
Ethernet Cable
POW ER PORT 1
Wireless Router
Gaming
Adapter
Powerline Ethernet Adapter
Ethernet Cable
POWER PORT 1 PORT 2 PORT 3 PORT 4
Ethernet Cable
Exis
ting
Ele
ctric
al W
irin
g
Router
Powerline
Ethernet
Adapter
POWER PORT 1 PORT 2 PORT 3 PORT 4
Direct to Router
Ethernet Cable
Router
POWER INTERNET
Modem
A DC IN 9V: Connect the AC adapter to this port. Do not
plug into the wall outlet at this time.
B DMex: Connect the small end of the USB cable to this
port.
C LAN: Connect an Ethernet cable (not supplied) to this
port.
D HDMI OUT: Connect the L-shaped end of the HDMI cable
to this port.
The BRAVIA TM Internet Video Link receiver is compatible with certain Sony televisions with the XMB
TM
(XrossMediaBar ® ) and DMe X interface. High-speed Internet access is also required.
Power off your TV before beginning the setup. The receiver can be installed either as a stand-alone or mounted to the back of your TV set.
OUT
LAN
DC IN 9V

NETW
ORK
INPUT SER VICE
%
$
#
"
OUT LAN DC IN 9V OUT LAN DC IN 9V
Front of
Receiver
z The rear view and location of the ports as shown may differ from your TV set.
OUT LAN DC IN 9V
% $ # "
B
1 Remove Cable Cover
Remove the cable cover to expose the ports
located on the bottom of the receiver.
Please read all instructions before beginning the installation.
Refer to the separate Attachment Guide for instructions on attaching to your TV.
B OUT LAN DC IN 9V
%
#
HDMI
DMex

NETWORK
Power LED
Network LED
Internet
Video Icon
Network Icon Video Icon
Media Category Bar
2 Connect Cables
Connect the cables in the order shown below.
3 Connect to TV
B Connect the large end of the USB cable
to the DMe X /SERVICE port on the TV.
D Connect the straight end of the HDMI cable
to any HDMI port on the TV.
4 Connect to the Internet
Connect an Ethernet cable to your Internet source by choosing one of the following recommendations for easy “plug and play.” Your receiver will automatically attempt to
connect to the Internet.
5
Verify Connection
a. Plug in the receiver and power on the TV.
b. Once the receiver and TV are powered on,
confirm the LED lights.
Standard Definition video: 802.11g
High Definition video: 802.11n
Standard Definition video: HomePlug Turbo,
HomePlug AV, UPA, HD-PLC
High Definition video: HomePlug AV, UPA, HD-PLC
6 Confirm Connection
Follow these instructions to confirm.
a. Press the DMe X button on your TV’s remote control
to view the connection status.
z If “Feature available with DMeX module” appears on the
screen, wait a few moments and try again.
b. When you see the message “Configuration Successful,”
press the HOME button on your TV’s remote control.
These menu icons associated with the receiver will appear
on the XMB
TM
(XrossMediaBar ® ).
z IMPORTANT: Do not press the INPUT button on the
remote control to access the BRAVIA™ Internet Video
Link. It is available on the XMB
TM
.
7 Enter Region
It is strongly recommended that you complete
Region Setup before using your receiver.
a. Highlight the Internet Video icon at the bottom of the
Settings menu on the XMB
TM
(XrossMediaBar ® ) and
press .
b. Highlight Region and press .
c. Follow the on-screen instructions to complete the setup.
z Default country is the United States. Press the B button
to select a different country.
8 Attach Cable Cover
Slide the cable cover back into place.
B
OUT LAN DC IN 9V OUT LAN DC IN 9V
Front of
Receiver
z For attachment options to the TV, see the separate
Attachment Guide.
When you see... Receiver...
Power
LED Green is powered “On.”
Red is not connected. Check all cable
components.
Orange is in update mode.
Network
LED Green is connected to the Internet.
Blinking
Green has network activity.