Sony CDX-GT62IPW User Manual

Fm/am compact disc player, Cdx-gt62ipw

Advertising
background image

SONY CDX-GT62IPW(US, ES) 3-285-540-

41 (1)

SONY CDX-GT62IPW(US, ES) 3-285-540-

41 (1)

3-285-540-

41 (1)

Cautions

• This unit is designed for negative ground (earth) 12 V

DC operation only.

• Do not get the leads under a screw, or caught in moving

parts (e.g. seat railing).

• Before making connections, turn the car ignition off to

avoid short circuits.

• Connect the

yellow and red power supply leads only

after all other leads have been connected.

Run all ground (earth) leads to a common

ground (earth) point.

• Be sure to insulate any loose unconnected leads with

electrical tape for safety.

• The use of optical instruments with this product will

increase eye hazard.

Notes on the power supply lead (yellow)

• When connecting this unit in combination with other

stereo components, the connected car circuit’s rating

must be higher than the sum of each component’s fuse.

• When no car circuits are rated high enough, connect

the unit directly to the battery.

iPod is a trademark of Apple Inc., registered in the U.S.

and other countries.

Parts Iist

• The numbers in the list are keyed to those in the

instructions.

• The bracket

 and the protection collar  are

attached to the unit before shipping. Before mounting

the unit, use the release keys

 to remove the bracket

 from the unit. For details, see “Removing the

protection collar and the bracket (

)” on the reverse

side of the sheet.

Keep the release keys

for future use as they

are also necessary if you remove the unit from

your car.

Caution

Handle the bracket

 carefully to avoid injuring your

fingers.

Catch

Note

Before installing, make sure that the catches on both sides of

the bracket

are bent inwards 2 mm (

3

/

32

in). If the catches are

straight or bent outwards, the unit will not be installed securely

and may spring out.

Installation/Connections
Instalación/Conexiones

FM/AM

Compact Disc Player

Connection example

Notes

Be sure to connect the ground (earth) lead before connecting

the amplifier.

The alarm will only sound if the built-in amplifier is used.

Connection diagram

To a metal surface of the car

First connect the black ground (earth) lead, then connect the

yellow and red power supply leads.

To the power antenna (aerial) control lead or

power supply lead of antenna (aerial) booster

Notes

It is not necessary to connect this lead if there is no power

antenna (aerial) or antenna (aerial) booster, or with a

manually-operated telescopic antenna (aerial).

When your car has a built-in FM/AM antenna (aerial) in

the rear/side glass, see “Notes on the control and power

supply leads.”

To AMP REMOTE IN of an optional power

amplifier

This connection is only for amplifiers. Connecting any other

system may damage the unit.

To the interface cable of a car telephone

To a car’s illumination signal

Be sure to connect the black ground (earth) lead to a metal

surface of the car first.

To the +12 V power terminal which is

energized in the accessory position of the

ignition switch

Notes

If there is no accessory position, connect to the +12 V

power (battery) terminal which is energized at all times.

Be sure to connect the black ground (earth) lead to a

metal surface of the car first.

When your car has a built-in FM/AM antenna (aerial) in

the rear/side glass, see “Notes on the control and power

supply leads.”

To the +12 V power terminal which is

energized at all times

Be sure to connect the black ground (earth) lead to a metal

surface of the car first.

Ч

2

Ч

4

Equipment used in illustrations (not supplied)
Equipo utilizado en las ilustraciones (no suministrado)

Rear speaker

Altavoz posterior

Front speaker

Altavoz frontal

Active subwoofer

Altavoz potenciador de

graves activo

Power amplifier

Amplificador de potencia

CDX-GT62IPW

© 2008 Sony Corporation

Printed in Thailand

Rotary commander RM-X4S

Mando rotatorio RM-X4S

3

1

2

4

5

6

7

L

R

REAR / SUB

AUDIO OUT

REMOTE

IN

FRONT

AUDIO OUT

REAR / SUB

AUDIO OUT

FRONT

BUS

IN

AMP REM

Max. supply current 0.3 A

Corriente máx. de alimentación de 0,3 A

Fuse (10 A)

Fusible (10 A)

Blue/white striped

Con rayas azules y blancas

ANT REM

Red

Rojo

Yellow

Amarillo

Black

Negro

Blue

Azul

White

Blanco

Green

Verde

Purple

Morado

White/black striped

Con rayas blancas y negras

Gray/black striped

Con rayas grises y negras

Green/black striped

Con rayas verdes y negras

Gray

Gris

Left

Izquierdo

Right

Derecho

*

1

RCA pin cord (not supplied)

*

2

Insert with the cord upwards.

*

1

Cable con terminales RCA

(no suministrado)

*

2

Insertar con el cable hacia arriba.

Purple/black striped

Con rayas moradas y negras

*

1

Max. supply current 0.1 A

Corriente máx. de alimentación de 0,1 A

from car antenna (aerial)

desde la antena del automóvil

Left

Izquierdo

Right

Derecho

*

1

*

2

A

B

FRONT

AUDIO OUT

REAR / SUB

AUDIO OUT

FRONT

AUDIO OUT

REAR / SUB

AUDIO OUT

ILLUMINATION

Light blue

Azul celeste

Orange/white striped

Con rayas naranjas y blancas

ATT

iPod

*

1

Notes on the control and power supply leads

The power antenna (aerial) control lead (blue) supplies +12 V

DC when you turn on the tuner.

When your car has built-in FM/AM antenna (aerial) in the rear/

side glass, connect the power antenna (aerial) control lead

(blue) or the accessory power supply lead (red) to the power

terminal of the existing antenna (aerial) booster. For details,

consult your dealer.

A power antenna (aerial) without a relay box cannot be used

with this unit.

Memory hold connection

When the yellow power supply lead is connected, power will

always be supplied to the memory circuit even when the ignition

switch is turned off.
Notes on speaker connection

Before connecting the speakers, turn the unit off.

Use speakers with an impedance of 4 to 8 ohms, and with

adequate power handling capacities to avoid its damage.

Do not connect the speaker terminals to the car chassis, or

connect the terminals of the right speakers with those of the

left speaker.

Do not connect the ground (earth) lead of this unit to the

negative (–) terminal of the speaker.

Do not attempt to connect the speakers in parallel.

Connect only passive speakers. Connecting active speakers

(with built-in amplifiers) to the speaker terminals may damage

the unit.

To avoid a malfunction, do not use the built-in speaker leads

installed in your car if the unit shares a common negative (–)

lead for the right and left speakers.

Do not connect the unit’s speaker leads to each other.
Note on connection

If speaker and amplifier are not connected correctly, “FAILURE”

appears in the display. In this case, make sure the speaker and

amplifier are connected correctly.

Precauciones

• Esta unidad se diseñó para alimentarse sólo con cc de

12 V de masa negativa.

• No coloque los cables debajo de ningún tornillo, ni

los aprisione con partes móviles (p. ej. los raíles del

asiento).

• Antes de realizar las conexiones, desactive el

encendido del automóvil para evitar cortocircuitos.

• Conecte los cables de entrada de alimentación

amarillo y rojo solamente después de haber

conectado los demás.

Conecte todos los cables de conexión a masa

a un punto común.

• Por razones de seguridad, asegúrese de aislar con cinta

aislante los cables sueltos que no estén conectados.

Notas sobre el cable de fuente de alimentación

(amarillo)

• Cuando conecte esta unidad en combinación con otros

componentes estéreo, la capacidad nominal del circuito

conectado del automóvil debe ser superior a la suma

del fusible de cada componente.

• Si no hay circuitos del automóvil con capacidad

nominal suficientemente alta, conecte la unidad

directamente a la batería.

iPod es una marca comercial de Apple Inc., registrada en

los EE. UU. y otros países.

Lista de componentes

• Los números de la lista corresponden a los de las

instrucciones.

• La unidad se comercializa con el soporte

 y el marco

de protección

 ya colocados. Antes de montarla,

utilice las llaves de liberación

 para extraer el

soporte

 de la misma. Para obtener más información,

consulte “Extracción del marco de protección y del

soporte (

)”.

Conserve las llaves de liberación

para

utilizarlas en el futuro, ya que también las

necesitará si retira la unidad del automóvil.

Precaución

Tenga mucho cuidado al manipular el soporte

 para

evitar posibles lesiones en los dedos.

Enganche

Nota

Antes de instalar la unidad, compruebe que los enganches de

ambos lados del soporte

están doblados hacia adentro 2 mm.

Si no lo están o están doblados hacia afuera, la unidad no se

instalará correctamente y puede saltar.

Ejemplo de conexiones

Notas

Asegúrese de conectar primero el cable de conexión a masa

antes de realizar la conexión del amplificador.

La alarma sonará únicamente si se utiliza el amplificador

incorporado.

Diagrama de conexión

A una superficie metálica del automóvil

Conecte primero el cable de conexión a masa negro,

y después los cables amarillo y rojo de entrada de

alimentación.

Al cable de control de la antena motorizada

o al cable de fuente de alimentación del

amplificador de señal de la antena

Notas

Si no se dispone de antena motorizada ni de amplificador

de antena, o se utiliza una antena telescópica accionada

manualmente, no será necesario conectar este cable.

Si el automóvil incorpora una antena de FM/AM en el

cristal trasero o lateral, consulte “Notas sobre los cables

de control y de fuente de alimentación”.

A AMP REMOTE IN de un amplificador de

potencia opcional

Esta conexión es sólo para amplificadores. La conexión de

cualquier otro sistema puede dañar la unidad.

Al cable de interfaz de un teléfono para

automóvil

A una señal de iluminación del automóvil

Asegúrese de conectar primero el cable de conexión a masa

negro a una superficie metálica del automóvil.

Al terminal de alimentación de +12 V que

recibe energía en la posición de accesorio

del interruptor de la llave de encendido

Notas

Si no hay posición de accesorio, conéctelo al terminal de

alimentación (batería) de +12 V que recibe energía sin

interrupción.

Asegúrese de conectar primero el cable de conexión a

masa negro a una superficie metálica del automóvil.

Si el automóvil dispone de una antena de FM/AM en el

cristal trasero o lateral, consulte “Notas sobre los cables

de control y de fuente de alimentación”.

Al terminal de alimentación de +12 V que

recibe energía sin interrupción

Asegúrese de conectar primero el cable de conexión a masa

negro a una superficie metálica del automóvil.

Notas sobre los cables de control y de fuente de

alimentación

El cable de control de la antena motorizada (azul) suministrará

cc de + 12 V cuando conecte la alimentación del sintonizador.

Si el automóvil dispone de una antena de FM/AM en el

cristal trasero o lateral, conecte el cable de control de antena

motorizada (azul) o el cable de entrada de alimentación

auxiliar (rojo) al terminal de alimentación del amplificador de

antena existente. Para obtener más información, consulte a su

distribuidor.

Con esta unidad no es posible utilizar una antena motorizada

sin caja de relé.

Conexión para protección de la memoria

Si conecta el cable de entrada de alimentación amarillo, el

circuito de la memoria recibirá siempre alimentación, aunque

apague el interruptor de encendido.
Notas sobre la conexión de los altavoces

Antes de conectar los altavoces, desconecte la alimentación

de la unidad.

Utilice altavoces con una impedancia de 4 a 8 con la

capacidad de potencia adecuada para evitar que se dañen.

No conecte los terminales de altavoz al chasis del automóvil,

ni conecte los terminales del altavoz derecho con los del

izquierdo.

No conecte el cable de conexión a masa de esta unidad al

terminal negativo (–) del altavoz.

No intente conectar los altavoces en paralelo.

Conecte solamente altavoces pasivos. Si conecta altavoces

activos (con amplificadores incorporados) a los terminales de

altavoz, puede dañar la unidad.

Para evitar fallas de funcionamiento, no utilice los cables de

altavoz incorporados instalados en el automóvil si la unidad

comparte un cable negativo común (–) para los altavoces

derecho e izquierdo.

No conecte los cables de altavoz de la unidad entre sí.
Nota sobre la conexión

Si el altavoz y el amplificador no están conectados

correctamente, aparecerá “FAILURE” en la pantalla. Si es así,

compruebe la conexión del altavoz y el amplificador.

Advertising