Advantech Industrial Mini-ITX Motherboard with DDR2/Dual GbE/PCI AIMB-221 User Manual
User manual aimb-221
Advertising
Table of contents
Document Outline
- AIMB-221
- 1 Hardware Configuration
- 1.1 Introduction
- 1.2 Features
- 1.3 Specifications
- 1.4 Jumpers and Connectors
- 1.5 Board Layout: Jumper and Connector Locations
- 1.6 AIMB-221 Block Diagram
- 1.7 Jumpers and Connectors
- 1.8 Safety Precautions
- 1.9 Jumper Settings
- 1.10 System Memory
- 1.11 Memory Installation Procedures
- 1.12 Cache Memory
- 1.13 Processor Installation
- 1.14 PCI Bus Routing Table
- 2 Connecting Peripherals
- 2.1 Introduction
- 2.2 Primary (IDE1) IDE Connector
- 2.3 DVI2 (Optional)
- 2.4 Front Panel Connectors (JFP1, JFP2, JFP3)
- 2.5 ATX/AT Mode Selector (JPSON1)
- 2.6 Serial Port Header (COM 3/4/5/6)
- 2.7 CPU Fan Connector (CPU Fan1)
- 2.8 System Fan (SYSFAN1, SYSFAN2)
- 2.9 Parallel Port (LPT1)
- 2.10 JSETCOM1
- 2.11 JSETCOM2
- 2.12 GPIO1
- 2.13 VGA HDMI
- 2.14 LAN1_USB12
- 2.15 LAN2_USB34
- 2.16 USB56
- 2.17 USB78
- 2.18 Audio
- 2.19 FPAUD1
- 2.20 SPKOUT1
- 2.21 Serial ATA Interface (SATA1, SATA2, SATA3, SATA4)
- 2.22 INV1
- 2.23 VGA2 (TV-Out) (Optional)
- 2.24 LVDS
- 2.25 LVDS POWER JUMPER (JLVDS1)
- 3 Award BIOS Setup
- 3.1 Introduction
- 3.2 Entering Setup
- 3.3 Standard CMOS Setup
- 3.4 Advanced BIOS Features
- Figure 3.3 Advanced BIOS Features screen
- 3.4.1 CPU Features
- 3.4.2 Hard Disk Boot Priority
- 3.4.3 Virus Warning
- 3.4.4 CPU L1, L2 & L3 Cache
- 3.4.5 Hyper-Threading Technology
- 3.4.6 Quick Power On Self Test
- 3.4.7 First/Second/Third Boot Device
- 3.4.8 Boot Other Device
- 3.4.9 Swap Floppy Drive
- 3.4.10 Boot Up Floppy Seek
- 3.4.11 Boot Up NumLock Status
- 3.4.12 Gate A20 Option
- 3.4.13 Typematic Rate Setting
- 3.4.14 Typematic Rate (Chars/Sec)
- 3.4.15 Typematic Delay (msec)
- 3.4.16 Security Option
- 3.4.17 APIC Mode
- 3.5 Advanced Chipset Features
- 3.6 Integrated Peripherals
- 3.7 Power Management Setup
- Figure 3.8 Power management setup screen
- 3.7.1 Power Supply Type
- 3.7.2 ACPI Function
- 3.7.3 ACPI Suspend Type
- 3.7.4 Run VGA BIOS if S3 Resume
- 3.7.5 Power Management
- 3.7.6 Video Off Method
- 3.7.7 Video Off In Suspend
- 3.7.8 Suspend Type
- 3.7.9 Suspend Mode
- 3.7.10 HDD Power Down
- 3.7.11 Soft-Off by PWR-BTTN
- 3.7.12 PowerOn by LAN
- 3.7.13 PowerOn by Modem
- 3.7.14 USB KB Wake Up From S3
- 3.7.15 PowerOn by Alarm
- 3.7.16 Primary IDE 0 (1) and Secondary IDE 0 (1)
- 3.7.17 FDD, COM, LPT PORT
- 3.7.18 PCI PIRQ [A-D]#
- 3.7.19 PWRON After PWR-Fail
- 3.8 PnP/PCI Configurations
- 3.9 PC Health Status
- 3.10 Frequency / Voltage Control
- 3.11 Password Setting
- 3.12 Save & Exit Setup
- 3.13 Exit Without Saving
- 4 Chipset Software Installation Utility and VGA Setup
- 5 LAN Configuration
- 6 AC97 Audio Setup
- A Programming the Watchdog Timer
- 1 Hardware Configuration