Document Outline

• AIMB-221
  • 1 Hardware Configuration
    • 1.1 Introduction
    • 1.2 Features
    • 1.3 Specifications
      • 1.3.1 System
      • 1.3.2 Memory
      • 1.3.3 Input/Output
      • 1.3.4 Ethernet LAN
      • 1.3.5 Industrial features
      • 1.3.6 Mechanical and environmental specifications
    • 1.4 Jumpers and Connectors
    • 1.5 Board Layout: Jumper and Connector Locations
      • Figure 1.1 Jumper and Connector locations
      • Figure 1.2 I/O connectors
    • 1.6 AIMB-221 Block Diagram
      • Figure 1.3 AIMB-221 Block Diagram
    • 1.7 Jumpers and Connectors
    • 1.8 Safety Precautions
    • 1.9 Jumper Settings
      • 1.9.1 How to set jumpers
      • 1.9.2 CMOS clear (JCMOS1)
        • Table 1.1: CMOS (JCMOS1)
      • 1.9.3 Watchdog timer output (JWDT1)
        • Table 1.2: Watchdog timer output (JWDT1)
        • Table 1.3: ATX/AT mode selector (JPSON1)
        • Table 1.4: COM1 RS-232 with 5V or 12V selector (JSETCOM1)
        • Table 1.5: COM2 RS-232/422/485 mode selector (JSETCOM2)
        • Figure 1.4 COM2 RS-232/422/485 jumper setting
    • 1.10 System Memory
      • 1.10.1 CPU FSB and memory speed
    • 1.11 Memory Installation Procedures
    • 1.12 Cache Memory
    • 1.13 Processor Installation
    • 1.14 PCI Bus Routing Table
      • Table 1.6: PCI Bus Routing Table
      • Table 1.7: PCI1 (Routing: AD31 / PCI_#INTF, #INTG, #INTH, #INTE)
      • Table 1.8: MINIPCI1 (Routing: AD28 / #INTE / #INTF)
  • 2 Connecting Peripherals
    • 2.1 Introduction
    • 2.2 Primary (IDE1) IDE Connector
    • 2.3 DVI2 (Optional)
    • 2.4 Front Panel Connectors (JFP1, JFP2, JFP3)
      • 2.4.1 ATX Soft Power Switch (JFP1)
      • 2.4.2 Reset Connector (JFP1)
      • 2.4.3 External Speaker (JFP2)
      • 2.4.4 HDD LED Connector (JFP2)
      • 2.4.5 SM Bus Connector (JFP2 PIN6,8)
      • 2.4.6 Power LED and keyboard lock connector (JFP3 / PWR_LED&KEY LOCK)
        • Table 2.1: ATX power supply LED status (No support for AT power)
    • 2.5 ATX/AT Mode Selector (JPSON1)
      • Table 2.2: ATX/AT Mode selector (PSON1)
    • 2.6 Serial Port Header (COM 3/4/5/6)
    • 2.7 CPU Fan Connector (CPU Fan1)
    • 2.8 System Fan (SYSFAN1, SYSFAN2)
    • 2.9 Parallel Port (LPT1)
    • 2.10 JSETCOM1
    • 2.11 JSETCOM2
    • 2.12 GPIO1
    • 2.13 VGA HDMI
    • 2.14 LAN1_USB12
    • 2.15 LAN2_USB34
    • 2.16 USB56
    • 2.17 USB78
    • 2.18 Audio
    • 2.19 FPAUD1
    • 2.20 SPKOUT1
    • 2.21 Serial ATA Interface (SATA1, SATA2, SATA3, SATA4)
    • 2.22 INV1
    • 2.23 VGA2 (TV-Out) (Optional)
    • 2.24 LVDS
    • 2.25 LVDS POWER JUMPER (JLVDS1)
  • 3 Award BIOS Setup
    • 3.1 Introduction
      • 3.1.1 BIOS Setup program
      • 3.1.2 CMOS RAM Auto-backup and Restore
    • 3.2 Entering Setup
      • Figure 3.1 Award BIOS Setup initial screen
    • 3.3 Standard CMOS Setup
      • Figure 3.2 Standard CMOS Features Screen
      • 3.3.1 Date
      • 3.3.2 Time
      • 3.3.3 IDE channel 0/1 Master/Slave
      • 3.3.4 Drive A / Drive B
      • 3.3.5 Video
      • 3.3.6 Halt On
      • 3.3.7 Memory
    • 3.4 Advanced BIOS Features
      • Figure 3.3 Advanced BIOS Features screen
      • 3.4.1 CPU Features
      • 3.4.2 Hard Disk Boot Priority
      • 3.4.3 Virus Warning
      • 3.4.4 CPU L1, L2 & L3 Cache
      • 3.4.5 Hyper-Threading Technology
      • 3.4.6 Quick Power On Self Test
      • 3.4.7 First/Second/Third Boot Device
      • 3.4.8 Boot Other Device
      • 3.4.9 Swap Floppy Drive
      • 3.4.10 Boot Up Floppy Seek
      • 3.4.11 Boot Up NumLock Status
      • 3.4.12 Gate A20 Option
      • 3.4.13 Typematic Rate Setting
      • 3.4.14 Typematic Rate (Chars/Sec)
      • 3.4.15 Typematic Delay (msec)
      • 3.4.16 Security Option
      • 3.4.17 APIC Mode
    • 3.5 Advanced Chipset Features
      • Figure 3.4 Advanced Chipset Features screen
      • 3.5.1 Memory Hole At 15M-16M
      • 3.5.2 Configure AMT BIOS Support (Intel Active Management Technology)
      • 3.5.3 PEG / Onchip VGA Control
      • 3.5.4 On-Chip Frame Buffer Size
      • 3.5.5 DVMT Mode
      • 3.5.6 DVMT / FIXED Memory Size
      • 3.5.7 Init Display First
    • 3.6 Integrated Peripherals
      • Figure 3.5 Integrated peripherals
      • Figure 3.6 On-Chip IDE Device
      • 3.6.1 IDE HDD Block Mode
      • 3.6.2 IDE DMA Transfer Access
      • 3.6.3 IDE Primary Master/Slave PIO/UDMA Mode (Auto)
      • 3.6.4 SATA Mode
      • 3.6.5 Legacy mode support
        • Figure 3.7 Onboard Device
      • 3.6.6 On board LAN1 ROM
      • 3.6.7 Onboard LAN2 Control
      • 3.6.8 On board LAN2 ROM
    • 3.7 Power Management Setup
      • Figure 3.8 Power management setup screen
      • 3.7.1 Power Supply Type
      • 3.7.2 ACPI Function
      • 3.7.3 ACPI Suspend Type
      • 3.7.4 Run VGA BIOS if S3 Resume
      • 3.7.5 Power Management
        • Table 3.1: Power Saving
      • 3.7.6 Video Off Method
      • 3.7.7 Video Off In Suspend
      • 3.7.8 Suspend Type
      • 3.7.9 Suspend Mode
      • 3.7.10 HDD Power Down
      • 3.7.11 Soft-Off by PWR-BTTN
      • 3.7.12 PowerOn by LAN
      • 3.7.13 PowerOn by Modem
      • 3.7.14 USB KB Wake Up From S3
      • 3.7.15 PowerOn by Alarm
      • 3.7.16 Primary IDE 0 (1) and Secondary IDE 0 (1)
      • 3.7.17 FDD, COM, LPT PORT
      • 3.7.18 PCI PIRQ [A-D]#
      • 3.7.19 PWRON After PWR-Fail
    • 3.8 PnP/PCI Configurations
      • Figure 3.9 PnP/PCI configurations screen
      • 3.8.1 Reset Configuration Data
      • 3.8.2 Resources Controlled By
      • 3.8.3 PCI / VGA Palette Snoop
      • 3.8.4 Maximum Payload Size
    • 3.9 PC Health Status
      • Figure 3.10 PC Health Status Screen
      • 3.9.1 Current System Temperature
      • 3.9.2 FAN1: CPU FAN Speed
      • 3.9.3 FAN2: System FAN Speed
      • 3.9.4 VCORE and Other Voltages
    • 3.10 Frequency / Voltage Control
      • Figure 3.11 Spread Spectrum Frequency/Voltage Control screen
      • 3.10.1 Spread Spectrum
    • 3.11 Password Setting
    • 3.12 Save & Exit Setup
    • 3.13 Exit Without Saving
  • 4 Chipset Software Installation Utility and VGA Setup
    • 4.1 Before you begin
    • 4.2 Windows XP Driver Setup
  • 5 LAN Configuration
    • 5.1 Introduction
    • 5.2 Features
    • 5.3 Installation
    • 5.4 Win XP Driver Setup (LAN)
  • 6 AC97 Audio Setup
    • 6.1 Introduction
    • 6.2 Windows XP Driver Setup (AC97)
  • A Programming the Watchdog Timer
    • A.1 Watchdog timer overview
    • A.2 Reset/Interrupt selection
    • A.3 Programming the Watchdog Timer
      • Table A.1: Watchdog timer registers
      • A.3.1 Example Programs