Panasonic TYWK42PV4W - Manual (Page 5)

5
English
5
4. Fit and fasten the plasma TV unit to the wall-hanging bracket.
(1) Locate the insulation spacers on the top of the plasma TV
unit into the notch on the top of the wall-hanging bracket,
and slide down.
(2) Lift the plasma TV unit a little, insert the bottom insulation
spacers into the holes on the bottom of the wall-hanging
bracket, and slide the unit down.
(3) Attach securely using the included unit fastening screws (1
each for left and right).
The bolt should be securely tightened to the torque given
below.
(1.2 - 1.5 N•m)
(1)
(3)
(2)
Wall-hanging bracket
Plasma TV
Top insulation spacer
Upper
notch
Lower hole
Lower
insulation
spacer
Fitting hole
for plasma
TV fastening
screw
W
all
Plasma TV fastening
screw
W
all
Note
• Be sure to securely tighten the fastening screws to keep the
plasma TV from becoming loose.
5. Preparation for wiring to equipment.
(2)
W
all
Wall-hanging
bracket
Plasma TV
㊍ Red screw for
open/close
fastening
Lock bracket
㊎ Lock bracket
fastening hole
㊍ Red screw
for open/
close
fastening
W
all
(1) Remove the red screws for open/close fastening (one each
on the left and right) ㊍ .
(2) Raise the plasma TV towards yourself, as shown in the
diagram at right, push up the lock bracket in the arrow
direction (upward), check that the bracket has locked,
and tentatively fasten. Securely fasten the red screw for
open/close fastening (one screw on left side) ㊍ to the lock
bracket fastening hole ㊎ .
(3) After the above preparation, wire to equipment.
The bolt should be securely tightened to the torque given
below.
(1.2 - 1.5 N•m)
6. Fastening of wall-hanging bracket.
(1)
Wa
ll
Lock
bracket
㊍ Red screw for
open/close
fastening
㊎ Lock bracket
fastening hole
㊍ Red screw for
open/close
fastening
㊏ Fitting hole
for red screw
for open/close
fastening
Wall-hanging
bracket
Wa
ll
(1) After wiring, remove the red screws for open/close fastening
(used when making wiring connections), raise the plasma
TV slightly, then slowly lower it back to the vertical position.
The lock will release.
(2) Securely fasten the red screws for open/close fastening
(one each for the left and right brackets) ㊍ tightly into the
fitting holes for red screws for open/close fastening ㊏ on
either side of the wall hanging bracket.
The bolt should be securely tightened to the torque given
below.
(1.2 - 1.5N•m)
Notes
• Pull back the plasma TV unit slowly when you set up it at the
original position.
• Be sure to always fit the red screws for open/close fastening
㊍ in order to fasten the plasma TV.
7. Removal of plasma TV unit.
(3)
(2)
Wall-hanging
bracket
(1) Screw for plasma TV unit
fastening
Lower Insulation
spacer
W
all
W
all
(1) Remove the screws for unit fastening (1 each on the left
and right) that are fitted to the wall-hanging bracket sides.
(2) While lifting the bottom of the plasma TV unit, pull it towards
yourself.
(3) When the lower insulation spacers are freed, keep lifting
upward.
TY-WK42PV4W_TQZH997-2_4048.indb 5 TY-WK42PV4W_TQZH997-2_4048.indb 5 2008/04/04 17:11:02 2008/04/04 17:11:02