Panasonic DMREH50 - Manual (Page 6)

2 6
6
RQTD0150-A
The GUIDE Plus+ System
The GUIDE Plus+ Information Panels
The content of the GUIDE Plus+ information panels can change.
The GUIDE Plus+ programme provider is responsible for the content of the information panels
(picture Q).
! Use [ ] to select these panels.
The GUIDE Plus+ Information Panels
7th Heaven Gilmore Girls
Die Abschl... Freunde...
SUB MENU
RETURN GUIDE
S
Time: 15:30 16:00 16:30
Prog. Type
All Types
15:00
12.1. Wed
Landscape 12.1.Wed 14:55
Abenteuer Wildnis ARD
ZDF
RTL
SAT1
RTL2
VOX
PRO7
PAGE-
PAGE+ v
v
...
Abenteuer Wild... Ta... Fliege-Die Talkshow
Derrick Heute in... Bianca-Wege...
Display Mode
Detektiv Duel M... Beyblade Yu-...
Das Familiengericht Das Jugendgericht
Richterin Barbara Sa... Richter Alexander...
Gilmore Girls
Die Abschl... Freunde... S.O.S Style & ...
...
7th Heaven 15:05~16:05
Q
Why does my GUIDE Plus+ System not receive any data ?
Check whether GUIDE Plus+ system setup was performed in full. / The GUIDE Plus+ system data is
updated several times each day. When the device is first connected, the GUIDE Plus+ system is not yet
ready to receive data. / The device takes approx. 1 hour (on average 30 minutes) to find the Host Channel.
After this, it takes up to 24 hours to load all of the data. / Switch your DVD recorder to Standby mode to
save the data. / Check whether the clock is properly set. / If signal quality is bad (ghost images or limited
reception), the GUIDE Plus+ system may not be able to receive any data. This problem may be solved with
a reception amplifier.
Why is the GUIDE Plus+ system only available after ca. 2
hours? The data rate, at which GUIDE Plus+ is sent, is limited. Depending on the country, signal quality and
number of channels received, the time until the GUIDE Plus+ system is ready can vary.
Why is "No Data" displayed for some or all stations?
These stations may not have been able to be identified automatically. => For these stations, select the “On”
in the SUB MENU under Editor and assign the correct reference station manually (page 5). / Some stations
are not supported by the GUIDE Plus+ system.
Why is the GUIDE Plus+ information not displayed
properly?
The reference station is not assigned correctly in the SUB MENU Editor (page 5). Select the correct
reference station. / There was a programme change. Check the current program, e.g. on the Web site for the
GUIDE Plus+ system provider or station provider.
How do I add or hide a station in the GUIDE Plus+ system?
For these stations, select “On” / “Off” manually in the SUB MENU under Editor (page 5). /
You can only view stations that are supported by the GUIDE Plus+ system.
What happens when the GUIDE Plus+ data transfer is
interrupted? The GUIDE Plus+ system shows the data that was received up to the interruption.
The programme information may be incomplete.
The Host Channel in France is Canal Plus. Do I have to
sign a contract with Canal Plus in order to be able to use
the GUIDE Plus+ system?
No, you can use the GUIDE Plus+ system without a contract.
Why was my GUIDE Plus+ data not updated?
The unit must be in Standby mode in order to update the data. If the unit is in EXT. Link mode (EXT LINK
lights up in the display), then the data update may also not work./ Make sure that the time is set correctly. /
Check whether "Timer Prog." is set under Auto Download Priority and change the setting in "GUIDE Plus+"
(page 5).
How often is the GUIDE Plus+ data updated and when?
The update frequency depends on the specific station (several times per day). / The data is updated
automatically when the unit is in Standby mode. / Select "GUIDE Plus+" under "Auto Download Priority"
(page 5). With this setting, an update will take place automatically between 2:50 and 5:10.
How does my unit behave during data transfer? During data transfer, "GUIDE" appears on your unit’s display and the unit’s fan switches on.
Is it possible to programme a recording, with a start and end
time that are different from the GUIDE Plus+ system?
You can manually change the start and end time of TIMER programmes in the TIMER RECORDING menu
(page 4).
Does the GUIDE Plus+ system support VPS/PDC?
The GUIDE Plus+ system works independently of VPS/PDC. However, you can programme TIMER
recordings with VPS / PDC in the TIMER RECORDING menu.
Why was the programme programmed with GUIDE Plus+
not recorded? The unit is not in TIMER standby (TIMER symbol " " lights up in the unit’s display). / Make sure that "GUIDE
Plus+" is selected under Auto Download Priority and change the setting to "Timer Prog." (page 5).
How can I record a programme if "No Data" is displayed in
the GUIDE Plus+ system?
Programme the Timer recording manually or via ShowView.
How can I cancel a TIMER programming?
The "T" symbol appears in the GUIDE Plus+ when a TIMER recording is programmed with the GUIDE Plus+
system. To cancel a TIMER RECORDING programming, press [PROG/CHECK]. Select the desired entry
and press [CANCEL] (page 4).
Can I receive GUIDE Plus+ system data via a connected
satellite receiver or a SetTop Box?
No, only via the built-in tuner. To perform timer recordings with satellite receivers or Set Top Boxes, please
use the External Link feature or your unit’s manual timer programming.
What happens when I unplug my unit from the power
outlet? The GUIDE Plus+ system data will not be updated. / If the unit is disconnected from the power supply for a
longer period of time, then the GUIDE Plus+ data is lost. / Make sure that the time is set again appropriately.
What happens if my postal code changes, e.g. if I move?
Change the postal code in the GUIDE Plus+ Setup menu (page 5). If necessary, perform a full Auto-Setup
(page 2). Saved GUIDE Plus+ data may be lost.
How can I reset my unit to its original default state?
Select "Shipping Condition" in the Setup menu. Attention: All settings and data are lost if you reset the unit to
its default state.
DATA
DOWNLOAD
RECORDING
GENERAL
SETUP
7th Heaven
-24 Hr +24 Hr
Info TIMER REC
Prog. Type
Questions and answers